Lincoln Electric POWER FEED 10M SINGLE/DUAL SVM172-A - Manual (Page 13)

POWER FEED 10M SINGLE/DUAL
INSTALLATION
A-7 A-7
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
CHANGING DRIVE ROLLS AND WIRE
GUIDES
FIGURE A.4
ITEM DESCRIPTION
1 Inner Wire Guide
2 Drive Rolls
3 Outer Wire Guide
To change drive rolls and wire guides:
1. Turn off power at the welding power source.
2. Open wire drive door.
3. Remove the outer wire guide. (Item #3)
4. Remove the 4 drive rolls (Item #2) by pulling them
straight off of the drive hub. Rock the upper drive
rolls back for ease of removal.
5. Remove the inner wire guide (Item #1).
6. Insert the new inner wire guide (Item #1) over the
locating pins of the feed plate.
7. Install each drive roll by pushing it onto the hub until
it fully seats.
8. Install the outer wire guide.
9. Swing the upper drive rolls down and close the wire
drive door.
WIRE DRIVE DOOR
(OPEN)
WIRE DRIVE SYSTEMS
Drive Roll Kits are designed to feed specific types and
wire sizes. The Power Feed 10M Single Wire Feeder
does not include these Drive Roll Kits with this Wire
Drive, but are available for ordering from the following
tables:
Drive Roll Kits, Steel Wires
Includes: 4 Smooth V groove drive rolls and an inner
wire guide.
KP1505-030S .023-.030 (0.6-0.8mm)
KP1505-035S .035 (0.9mm)
KP1505-045S .045 (1.2mm)
KP1505-052S .052 (1.4mm)
KP1505-1/16S 1/16 (1.6mm)
Drive Roll Kits, Cored Wires
Includes: 4 Knurled drive rolls and an inner wire guide.
KP1505-035C .030-.035" (0.8-0.9mm)
KP1505-045C .040-.045" (1.0-1.2mm)
KP1505-052C .052" (1.4mm)
KP1505-1/16C 1/16" (1.6mm)
Drive Roll Kits, Steel or Cored Wires
Includes: 4 Knurled drive rolls and an inner wire guide.
KP1505-068 .068-.072" (1.8mm)
KP1505-5/64 5/64" (2.0mm)
KP1505-3/32 3/32" (2.4mm)
KP1505-7/64 7/64" (2.8mm)
KP1505-.120 .120" (3.2mm)
Drive Roll Kits, Hardfacing Wires
Includes: 2 Knurled drive rolls, 2 Smooth V groove
drive rolls and an inner wire guide.
KP1505-7/64C 7/64" (2.8mm)
Drive Roll Kits, Aluminum Wire
Includes: 4 polished U groove drive rolls, outer wire
guide and an inner wire guide.
KP1507-035A .035" (0.9 mm)
KP1507-040A .040" (1.0mm)
KP1507-3/64A 3/64" (1.2mm)
KP1507-1/16A 1/16" (1.6mm)
KP1507-3/32A 3/32" (2.4mm)