Lincoln Electric POWER FEED 10M SINGLE/DUAL SVM172-A - Manual (Page 96)

POWER FEED 10M SINGLE/DUAL
ACCESSORIES
CC-6 CC-6
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
K1733-1 WIRE STRAIGHTENER
Install per the Instructions shipped with the Kit.
K2339-1 PUSH-PULL KIT AND K2320-1
FOOT AMPTROL AMPHENOL
The push-pull kit provides direct connection of a Cobra
Gold or Prince XL torch to the
Power Feed 10M Dual Wire
Feeder wire feeder.
The kit is intended for use with the following Cobra
Max, Python or Prince XL torches:
Cobra Max
K2252-1 Air Cooled 15ft.(4.5m)
K2252-2 Air Cooled 25ft.(7.6m)
Python
K2212-1 Water Cooled 15ft.(4.5m)
K2211-2 Air Cooled 25ft.(7.6m) K2212-2 Water Cooled 25ft.(7.6m)
K2211-3 Air Cooled 50ft.(15.6m) K2212-3 Water Cooled 50ft.(15m)
Prince XL
K1592-1 Water Cooled 15ft.(4.5)
K2296-2 Air Cooled 25ft.(7.6) K1592-2 Water Cooled 25ft.(7.6)
K1592-3 Water Cooled 50ft.(15.6 )
Remove all input power to the Power Feed 10M
Dual Wire Feeder before installing the Connection
Adapter Kit.
------------------------------------------------------------------------
Refer to the Owner’s Manual of the Torch for
Amperage and Duty Cycle rating information. The
torch rating may not match the rating of the power
source.
------------------------------------------------------------------------
MAKING A WELD WITH THE PRINCE XL
OR COBRA GOLD TORCH INSTALLED
• Set the idle roll pressure on the wire drive between an
indicator reading of 0-2. A recommended start point is
1.5.
• Depending on the weld mode, set the Voltage or Trim
at the Power Feed 10M Dual Wire Feeder using the right
control knob located on the upper case front panel.
• The Wire Feed Speed (WFS) is set using the control
knob on the Torch. The left control knob on the Power
Feed 10M Dual Wire Feeder is inactive. The actual WFS
being set at the torch is displayed on the Power Feed
10M Dual Wire Feeder .
• All weld parameters normally available for the active
weld mode are available during push-pull operation.
Refer to the Operation Section of this manual.
K659-1 GAS GUARD REGULATOR
Adjustable flow regulator with removable adjuster key for
CO2 and Argon blend gases. Mounts onto feeder inlet,
and reduces gas waste and arc start “blow” by reducing
surge caused by excess pressure in supply hose.
Install the 5/8-18 male outlet of the regulator to the 5/8-18
female gas inlet on the back panel of the wire drive.
Secure fitting with flow adjuster key at top. Attach gas
supply to 5/8-18 female inlet of regulator per INSTALLA-
TION section.
K1556-1 LIGHT DUTY CASTER KIT
This option provides 4 casters and all required hardware
to mount it to the Power Feed Wire Feeder.
K1555-2 INSULATED LIFT HOOK
For applications where an insulated lift hook is required.
This kit provides an easily installed, heavy duty insulated
lift eye that mounts to the wire reel stand mast. See the
instructions provided with the kit for installation.
K1546-1 CONDUIT ADAPTER
Install per the Instructions shipped with the Kit.
K1551-2 INCOMING BUSHING (4 Ball Roller)
(Standard on codes 10600 and up)
This ball bearing equipped incoming bushing can be
used in place of the standard incoming wire bushing,
when feeding solid steel or cored wire electrodes. It
significantly reduces any abrasion to the electrode wire
where it enters the feed head. This results in even
smoother, more trouble free operation.
CAUTION
WARNING