Lincoln Electric POWER FEED 10M SINGLE/DUAL SVM172-A - Manual (Page 73)

POWER FEED 10M SINGLE/DUAL
OPERATION
BB-5 BB-5
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Se
ct
io
n
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
Re
tu
rn
to
Ma
st
e
r
T
O
C
3. OUTPUT CONTROLS
• The Power Feed 10M Dual Wire Feeder has 2
encoder knobs to adjust weld parameters.
• Each encoder changes the displayed value of the
meter located directly above that encoder.
• In CC-GTAW modes when equipped with a foot or
hand amptrol, the left encoder sets the maximum
welding current. Full depression of a foot or hand
amptrol results in the preset level of current.
• In CC-Stick and CC-GTAW, the right encoder acti-
vates and de-activates the output. Turning the
encoder clockwise enables the output. To de-ener-
gize the output, turn the encoder counter-clockwise.
The display above will indicate the "ON" or "OFF"
status of the output.
4. DUAL PROCEDURE / DUAL HEAD SELECT
W/MEMORY PANEL
(See Mode Select Panel Section for a Functional
Description and detailed explanation)
This panel is intended for dual head applications, and
is essentially the same as the Dual Procedure with
Memory panel except for the addition of a second pro-
cedure select push button. It contains two procedure
select buttons, one for each head, and six memory
(storage) buttons.
In general terms, dual procedure and memory are
essentially independent storage locations for informa-
tion.
5. MODE SELECT PANEL 4 (MSP4)
OVERVIEW:
The MSP4 is the standard mode select panel for the
Power Feed 10M Dual Wire Feeder wire feeders. The
MSP4 is capable of:
- Weld mode selection.
- Arc Control adjustment.
- Weld sequence control (Preflow Time, Run-in
WFS, etc.)
ITEM DESCRIPTION
1 IR (Infrared) Port.
2 Weld Mode Number.
3 Weld Wire Type.
4 Wire Size.
5 Weld Mode Description.
6 Status LED Lights-Weld Mode/Arc Control.
7 Selection Pushbutton Weld Mode or Arc
Control.
8 “Set” (Adjustment) Dial / Knob
9 Selection Pushbutton Start and End
Options.
10 Status LED Lights-Start/End Options.
Through the use of alphanumeric displays, the MSP4
provides standard text messages designed to
enhance the user’s understanding of the machine’s
operation as well as provide advanced capabilities
The panel provides:
• Clear identification of the selected weld mode.
• Identification of weld modes not listed on the
preprinted weld mode list label.
• Control of up to four wave controls (arc controls.)
• Weld mode specific wave control name display
(Peak, Background, Pinch, etc.).
• Unit values are displayed (Amps, in/min, etc.).
• User-friendly machine setup and configuration.
• Limit setting for restricting the operators range of
control.
• Lockout to prevent unauthorized changes to
machine configuration.
Additionally, the MSP4 includes an infrared (IR) port
for wireless communication and configuration using a
Palm OS based hand held computer and a simplified
control layout.
START OPTIONS
END OPTIONS
SET
SETUP
IR PORT
PULSE 4043 Ar
3/64"
ALUMINUM
72
WELD MODE
ARC CONTROL
2 1
3 4 5
6 10 7 8 9
FIGURE BB.2