Phonetics IMS-4000 User Manual
Ims-4000
Advertising
Table of contents
Document Outline
- Important Safety Instructions
- Chapter 1: Installation
- Introduction
- About This Manual
- HOST INSTALLATION and CONFIGURATION
- Physical Description
- Installation
- Operating Environment
- Network Configuration
- Battery Maintenance
- IMS Host Specifications
- Operating Specifications
- Communications Specifications
- Environmental Monitoring
- NODE INSTALLATION & CONFIGURATION
- Physical Description
- Installation
- Operating Environment
- Network Configuration
- Node Specifications
- Operating Specifications
- Communications Specifications
- Environmental Monitoring
- Chapter 2: IMS-4000 Software
- Introduction
- IMS-4000 Quick Start Guide
- Install Units and Configure Network Settings
- Install Software and Log In to Host
- Default Username and Password
- Configure the Unit Properties for the Host and Node(s)
- Configure Input Templates
- Connect Environmental Sensors to Host and Node(s)
- Configure User Profiles and Contacts
- Configure IP Alarms
- Record and Assign Voice Messages
- Software Installation and Hardware Requirements
- Hardware and Software Requirements
- Software Installation
- Configuring Hosts and Nodes
- Setting Up An Enterprise
- Setting the Unit Properties for the IMS Host
- Changing Host Network Settings using ConsoleView
- Setting the Unit Properties for the Node
- Changing Node Network Settings
- Configuring Environmental Inputs
- Alarm Response via the PowerGate, PowerGate2, or Camera
- High Sound Alarms
- Realtime Strip Chart
- Environmental Input Alarm Logic
- Trouble Alarms
- Removing/Changing a Sensor
- Configuring IP Alarms
- IP Alarm Setup
- Alarm Logic
- Input/Alarm Classes
- Configuring User Profiles and Contacts
- Configuring User Profiles
- Adding a Profile
- Contacts
- Alarm Delivery Options
- Saving and Loading Programming
- Reconnecting
- Recording and Uploading Voice Messages
- Holiday Setup
- Alarm Message Pop-Ups
- E-Mail Setup and Two-Way E-Mail Commands
- Configuring a Video Camera
- Web Page
- Graphs
- History
- Datalog History
- Updating Firmware
- Chapter 3: Operation
- Chapter 4: SNMP (Simple Network Management Protocol)
- Chapter 5: PowerGate
- Physical Description
- Installation
- Rack Mount Installation
- Wall Mount Installation
- Tabletop Installation
- Connection to IMS-4000 Host or Node
- Operation
- Plugging In Equipment
- PowerGate Setup via the IMS ConsoleView Software
- Switching Outlets using the IMS ConsoleView Software
- IMS PowerGate Specifications
- Chapter 6: PowerGate2
- Physical Description
- Front Panel Layout
- Rear Panel
- Installation
- Rack Mount Installation
- Wall Mount Installation
- Tabletop Installation
- Connection to IMS-4000 Host or Node
- Operation
- Connect Input Power
- Plugging In Equipment
- PowerGate2 Setup via the IMS ConsoleView Software
- IMS PowerGate2 Specifications
- Chapter 7: IMS-4000 Sensors
- IMS-4810 Room Temperature Sensor
- Installation Instructions
- IMS-4811 Room Temperature Sensor with display
- Installation Instructions
- IMS-4812 Mini–Temperature Sensor (Fahrenheit)
- Installation Instructions
- IMS-4813 Room Temperature Sensor with display (Celsius)
- Installation Instructions
- IMS-4820 Room Humidity Sensor
- Installation Instructions
- IMS-4821 Room Humidity Sensor with display
- Installation Instructions
- IMS-4830 Water Detection Sensor
- Installation Instructions
- IMS-4840 External Power Sensor
- Installation Instructions
- IMS-4850 Dry Contact Bridge
- Installation Instructions
- IMS-4851 4–20mA Bridge
- Installation Instructions
- IMS-4860 Door Switch
- IMS-4861 Passive Infrared Detection Sensor
- Appendix A: Weekly Testing Procedure
- Appendix B: Troubleshooting
- Appendix C: IMS-4000 Accessories
- Appendix D: License Agreement for Sensaphone® IMS-4000 ConsoleView Software
- Appendix E: Returning an IMS Unit for
- Test Log