NEC PlasmaSync 42PD3 - Manual (Page 45)

P LASMA M ONITOR Ⅵ Ⅵ Ⅵ †
45
Move the cursor up and down with
the POSITION/CONTROL
▲▼
buttons.
[LUM. LIMIT]:
Suppresses the brightness of
the screen.
[ORBITING]:
Moves the screen at a fixed pe-
riod.
* Cannot be set at the time of the 4-screen/9-screen
multiple system setting.
[INV/WT]:
Displays a negative/positive inverse image or an all-white
screen.
* The [INV] and [WT] settings will be switched to [OFF]
when the power is switched on or off, and at the time of
input signal selection. The last operating condition data
will not be stored in memory.
[PROG. ORBIT... ➝]:
Align the cursor with [PROG. ORBIT... ➝] and press the
PROCEED button. The PROG. ORBIT MENU screen is
displayed and the movement of screen dots can be set
to be programmable.
* When either [ORBITING] or [PROG. ORBIT] is set to
[ON], the other one will be [OFF].
* Note that if [PROG. ORBIT] is set to [ON], the dot display of
the set portion will be lost on the screen
* This setting is not available when the 4-screen/9-screen
multiple system is set.
[LUM. LIMIT] and [ORBITING] settings
[ON] : Long life function is operational.
[OFF] : Cancelled
[INV/WT] settings
[INV] : Provides the negative/positive inverse image of the
screen.
[WT] : Displays an all-white screen.
[OFF] : Cancelled
[PROG. ORBIT... ➝] settings
[SET] :
[ON] : Function is operational.
[OFF] : Cancelled.
[H-DOT] :
Moves from 1 to 20 dots in the
horizontal direction.
[V-LINE] :
Moves from 1 to 20 dots in the
vertical direction.
[TIME] :
A 1- to 5-minute interval between movements.
Long Life Settings (LONG LIFE MODE)
Preparation Press the PROCEED button to display the main menu.
1 Align the cursor with
2
Move the cursor left and right with
the POSITION/CONTROL
ᮤ ᮣ
buttons.
LUM. LIMIT
ORBITTING
INV / WT
PROG. ORBIT . . . . . . . .
GRAY LEVEL
ALL RESET : OFF
: OFF
: OFF
: 3
LONG LIFE MODE
LUM. LIMIT
ORBITTING
INV / WT
PROG. ORBIT . . . . . . . .
GRAY LEVEL
ALL RESET : OFF
: OFF
: OFF
: 3
LONG LIFE MODE
Align the cursor with the desired item
These settings reduce screen burn-in.
Set [OSD MODE] to [PRO] on the configuration menu, then per-
form the following operations.
Long Life Settings (LONG LIFE MODE)
4
3 Set the long life mode with the POSI-
TION/CONTROL ᮤ ᮣ buttons
Press the EXIT button 2 times
Press the EXIT button one time to return to the main menu.
One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all long life settings to the default
settings.
SET
H-DOT
V-LINE
TIME
: OFF
: 5
: 5
: 1
PROG. ORBIT MENU
Important
■ Regarding Copyright
Please note that using this monitor for the purpose of commercial gain or
the attraction of public attention in a venue such as a coffee shop or hotel
and employing compression or expansion of the screen image with a
wide screen setting (of FULL, ZOOM, or STADIUM), etc., raises concern
about the infringement of copyright rights which are protected by copy-
right law.