Roland VP-770 - Manual (Page 101)

101
SYSTEM S1/S2
Here you can specify the functions that will be controlled by the [S1]/[S2] buttons.
Parameter Value Description
Sw Source REGIST, SYSTEM The assignments for the [S1]/[S2] buttons can be stored individually in each
registration. When you select a diff erent registration, this setting specifi es
whether the [S1]/[S2] buttons will be given the assignments stored in the
registration (REGIST), or the assignments stored in the system settings for
the entire VP-770 (SYSTEM).
Sw1 Assign
Sw2 Assign Specify the functions that will be controlled by the [S1]/[S2] buttons.
OFF Off
PIZZ/STAC The pizzicato or staccato sound will be heard (only for supported tones).
FALL/TREM The fall or tremolo sound will be heard (only for supported tones).
UNI/STK Switches between unison mode and stack mode (only for supported tones).
DOIT Applies the doit eff ect (only for supported tones).
PORT-ENS Applies the portamento eff ect to the Ensemble.
PORT-VOC Applies the portamento eff ect to the Vocal Designer.
AMB-OFF Switches the ambience when you press the button.
DIR-MIC-OFF Switches the direct microphone when you press the button.
Sw1 Mode
Sw2 Mode Turns the [S1]/[S2] buttons function LATCH/MOMENTARY.
LATCH The on/off status will alternate each time you press [S1]/[S2] button.
MOMENTARY The status will be on only while you hold down [S1]/[S2] button.
SYSTEM D BEAM
Here you can specify the function that will be controlled by the D Beam.
Parameter Value Description
D Beam Source REGIST, SYSTEM The assignments for the D beam can be stored individually in each
registration. When you select a diff erent registration, this setting specifi es
whether the D beam will be given the assignments stored in the registration
(REGIST), or the assignments stored in the system settings for the entire
VP-770 (SYSTEM).
D Beam Sens 0–127 This sets the D Beam controller’s sensitivity. Increasing this value will raise
the sensitivity.
DB1 Select
DB2 Select
DB3 Select FIX, ASGN When a D Beam button is on, this setting specifi es whether it will perform
the function printed on the panel (FIX) or the function assigned by the DB1
–3 Asgn settings (ASGN).
You can switch between FIX and ASGN at any time by holding down the
D Beam button for several seconds. *
DB1 Asgn
DB2 Asgn
DB3 Asgn MOD, DYN1, DYN2,
EXP, FILTER, WAH,
PIZZ/STAC, FALL/TREM,
UNI/STK, DOIT, PORT,
PITCH These settings specify the function that will be controlled by the D Beam
when DB1–3 Select is set to “ASGN.”
For details on each value, refer to p. 85. *
DB1 Range Lo
DB2 Range Lo
DB3 Range Lo 0–127 Specifi es the depth of the eff ect when the D Beam controller is not
responding. Increasing this value will apply an eff ect even if the D Beam
controller is not responding at all.
DB1 Range Hi
DB2 Range Hi
DB3 Range Hi 0–127 Specifi es the depth of the eff ect when the D Beam controller is responding
to its maximum extent. Reducing this value will reduce the amount of eff ect
produced by the D Beam controller.
DB1 Polarity
DB2 Polarity
DB3 Polarity STANDARD, REVERSE Inverts the change that occurs when you move your hand above the sensor.
DB1 Part
DB2 Part
DB3 Part Specifi es the part(s) that will be controlled by the D Beam.
VOC/ENS Vocal Designer part and Ensemble part.
VOC Vocal Designer part only.
ENS Ensemble part only.