Tascam HS-4000 - Manual (Page 76)

76
TASCAM HS-4000
10 – Internal settings
I/O page
Set the synchronization signal status display and time code
output on this page.
STATUS
This shows the status of synchronization signals.
TIMECODE IN:
When time code is input, the time code frame rate is shown.
WORD/VIDEO IN:
When a synchronization signal is detected at this connector,
WORD , VIDEO or TriLevel is shown.
TC Out Mode
Use the buttons to set the time code output mode.
GenOut button:
Time code is output from the internal time code generator.
PlayOut button (default):
In timeline mode, the time code time for playback and
recording is output. In take and playlist modes during
playback, the time code recorded in the file is output.
Remote settings (REMOTE SETUP)
Make settings for the PARALLEL, RS-232C and RS-422
connectors.
The
REMOTE SETUP screen has 4 pages: GENERAL . PARALLEL ,
RS-232C and RS-422 . Touch the tabs at the bottom of the
screen to open the corresponding page.
GENERAL page
Make flash start key settings on this page.
Flash Start Key Method
Set how the flash start key operates.
This function is planned for a future firmware version upgrade.
Currently, the setting cannot be changed from
Flash Start .
Flash Start button (default):
Touch a flash start key to start flash playback.
Standby button:
When stopped, touch a flash start key to start playback
standby. Then, press the PLAY key to start playback.
During playback, touching another flash start key will cause
the corresponding take or entry to become lined up for
playback. Press the PLAY key to start playback of that entry.
If the
Play Mode is set to All Take , when the currently
playing entry completes playback, the entry that is lined up
will start playing. If the
Play Mode is set to One Take ,
when the currently playing entry completes playback, the
entry that is lined up will start playback standby.
RC–HS32PD Flash Start Key Mode
This sets the number of flash start keys for a TASCAM
RC–HS32PD remote controller (sold separately) in dual playlist
mode.
16x2 keys button:
16 keys can be used by both A and B for a total of 32 keys.
12x2 keys button:
12 keys can be used by both A and B for a total of 24 keys.
NOTE
In take mode and single playlist mode, 32 keys are always used.
FADER MODE
Set whether faders on an external TASCAM RC-HS32PD remote
controller (sold separately), for example, are enabled or not.
When set to
Disable , the internal fader is fixed at 0 dB.
Setting buttons: Disable , Enable (default)
FADER Start MODE
When the fader start function of an external TASCAM RC-HS32PD
remote controller (sold separately), for example, is on, set whether
fader start, which allows you to start playback by raising the fader
from
when in playback standby, is enabled or not.
Setting buttons: Disable , Enable (default)
FADER Stop MODE
When the fader start function of an external TASCAM RC-HS32PD
remote controller (sold separately), for example, is on, set whether
fader stop, which allows you to put playback into standby by
lowering the fader to
during playback, is enabled or not.
Setting buttons: Disable , Enable (default)
NOTE
If both the FADER Start MODE and FADER Stop MODE items are set to
Disable , the fader start function of the external TASCAM RC-HS32PD
remote controller (sold separately) will be turned off automatically, and the
FADER START indicator will turn off. In this state, if you press the Fader Start
key on the TASCAM RC-HS32PD remote controller, a “Cannot Change Now.
Fixed in current mode” warning appears in a pop-up window.
PARALLEL page
Set the AUX 1-3 functions of the PARALLEL connector.
AUX Assign
Touch a knob to select it, making the background yellow, and
turn the DATA dial to set the parameter.
The parameters that can be selected include
F.FWD , REW , MARK ,
MARK SKIP– , MARK SKIP+ , ONLINE , CALL and FADER START
B .
● AUX1 Function:
Set the function of PARALLEL connector pin 17 (AUX1)
(default:
MARK SKIP+ ).
● AUX2 Function:
Set the function of PARALLEL connector pin 18 (AUX2)
(default:
MARK SKIP– ).
● AUX3 Function:
Set the function of PARALLEL connector pin 19 (AUX3)
(default:
MARK ).