Pioneer SC-LX82 - Manual (Page 109)

The Advanced MCACC menu 11
109
En
After this, perform the Full Auto MCACC procedure
again.
– If the connections were right, select
GO NEXT and
continue.
8 Make sure ‘OK’ is selected, then press ENTER.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, and Acoustic Calibration EQ.
Again, try to be as quiet as possible while this is
happening. It may take 3 to 7 minutes.
• If you selected a STAND.WAVE Multi-Point setup
(in step 2), you will be asked to place the mic at the
2nd and 3rd reference points before finally placing it
at your main listening position.
9 The Auto MCACC Setup procedure is completed and
the Advanced MCACC menu reappears automatically.
The settings made in the Auto MCACC Setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
Manual MCACC setup menu (starting below) or Manual
SP Setup menu (starting on page 121).
1
You can also choose to view the settings by selecting
individual parameters from the
MCACC Data Check
screen:
• Speaker Setting – The size and number of speakers
you’ve connected (see page 121 for more on this)
• Channel Level – The overall balance of your speaker
system (see page 110 or 122 for more on this)
• Speaker Distance – The distance of your speakers
from the listening position (see page 111 or 123 for
more on this)
2
• Standing Wave – Filter settings to control lower
‘boomy’ frequencies (see page 111 for more on this)
• Acoustic Cal EQ – Adjustments to the frequency
balance of your speaker system based on the
acoustic characteristics of your room (see page 112
for more on this)
• Group Delay – The original characteristics of group
delay of the speakers calibrated and the targeted
characteristics can be displayed graphically (see
Group Delay on page 117 for more on this).
• Output PC – The data transfer mode with the
connected computer is set. The graphs of the reverb
characteristics and group delay characteristics
before and after calibration and the various MCACC
parameters can be checked (see
Output PC on
page 117 for more on this).
Press RETURN after you have finished checking each
screen. When you’re finished, select RETURN to go back
to the HOME MENU.
Be sure to disconnect the microphone from this receiver
upon completion of the Auto MCACC Setup.
Manual MCACC setup
You can use the settings in the Manual MCACC setup
menu to make detailed adjustments when you’re more
familiar with the system. Before making these settings,
you should have already completed
Automatically setting
up for surround sound (Auto MCACC & Full Band Phase
Control) on page 45.
You only need to make these settings once (unless you
change the placement of your current speaker system or
add new speakers).
CAUTION
• The test tones used in the Manual MCACC setup are
output at high volume.
Important
• You will need to first specify the MCACC preset you
want to adjust by pressing MCACC before pressing
HOME MENU (step 2 in Making receiver settings from
the Advanced MCACC menu on page 106).
• For some of the settings below, you’ll have to connect
the setup microphone to the front panel and place it
about ear level at your normal listening position.
Press
HOME MENU to display the HOME MENU
before you connect the microphone to this receiver. If
the microphone is connected while the
HOME
MENU is not being displayed, the display will change
to the
Full Auto MCACC under Advanced MCACC.
Note
1 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm will end up with different size
settings. You can correct the setting manually using the Manual speaker setup on page 121.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking
delay and room characteristics into account) and generally does not need to be changed.
• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing environment, we recommend
adjusting the settings manually.
2 Since the distance measurements have been set according to the sound characteristics of your speakers, there are cases where (for optimal
surround sound) the actual distance may differ from the speaker distance setting.
Now Analyzing...
1b.Auto MCACC
A/V RECEIVER
Exit Cancel
Subwoofer Check :
Now Analyzing... 5/10
Surround Analysis
1b.Auto MCACC
A/V RECEIVER
Exit Cancel
Speaker System : OK
Channel Level :
Speaker Distance :
Standing Wave
:
Reverb :
Aco Cal EQ Pro
:
SC-LX82_LX72.book Page 109 Thursday, April 23, 2009 7:05 PM