Connecting an ir receiver, Connecting your equipment 03 – Pioneer SC-LX82 User Manual
Page 39
Connecting your equipment
03
39
En
Connecting an IR receiver
If you keep your stereo components in a closed cabinet or
shelving unit, or you wish to use the sub zone remote
control in another zone, you can use an optional IR
receiver (such as a Niles or Xantech unit) to control your
system instead of the remote sensor on the front panel of
this receiver.
1
1
Connect the IR receiver sensor to the IR IN jack on
the rear of this receiver.
2
Connect the IR IN jack of another component to the
IR OUT jack on the rear of this receiver to link it to the
IR receiver.
Please see the manual supplied with your IR receiver for
the type of cable necessary for the connection.
• If you want to link a Pioneer component to the IR
receiver, see
Operating other Pioneer components
with this unit’s sensor below to connect to the
CONTROL jacks instead of the IR OUT jack.
Operating other Pioneer components
with this unit’s sensor
Many Pioneer components have
SR CONTROL jacks
which can be used to link components together so that
you can use just the remote sensor of one component.
When you use a remote control, the control signal is
passed along the chain to the appropriate component.
2
Important
• Note that if you use this feature,
make sure that you
also have at least one set of analog audio, video or
HDMI jacks connected to another component for
grounding purposes.
1
Decide which component you want to use the
remote sensor of.
When you want to control any component in the chain,
this is the remote sensor at which you’ll point the
corresponding remote control.
2
Connect the CONTROL OUT jack of that component
to the CONTROL IN jack of another Pioneer component.
Use a cable with a mono mini-plug on each end for the
connection.
Continue the chain in the same way for as many
components as you have.
Note
1 • Remote operation may not be possible if direct light from a strong fluorescent lamp is shining on the IR receiver remote sensor window.
• Note that other manufacturers may not use the IR terminology. Refer to the manual that came with your component to check for IR
compatibility.
• If using two remote controls (at the same time), the IR receiver’s remote sensor takes priority over the remote sensor on the front panel.
LAN
(10/100)
S
OPTICAL
RS-232C
HDMI
IR
CONTROL
BD
IN
12 V
TRIGGER
IN
1
IN
2
IN
3
OUT
1
OUT
2
OUT 1
OUT 2
ASSIGNABLE
3
1
-
(KURO
LINK )
ASSIGNABLE
COAXIAL
ASSIGNABLE
(CD-R)
IN
4
(VIDEO1)
IN
3
(DVR)
IN
2
(TV/SAT)
IN
1
IN
3
(VIDEO 2)
IN
2
(CD)
IN
1
(DVD)
(OUTPUT
12V
TOTAL
50 mA
MAX)
1
2
IN
1
IN
IN
2
OUT
OUT
(D
P
R
IR
CONTROL
IN
1
IN
IN
2
OUT
OUT
IN
OUT
CONTROL
IN
IR
IR receiver
Closet or shelving unit
Non-Pioneer
component
Pioneer
component
2 • If you want to control all your components using this receiver’s remote control, see
Setting the remote to control other components on page 93
(SC-LX82)/page 100 (SC-LX72).
• If you have connected a remote control to the
CONTROL IN jack (using a mini-plug cable), you won’t be able to control this unit using the
remote sensor.
LAN
(10/100)
SPEAKERS
CAUTION:
SPEAKER IMPEDANC
ATTENTION
ENCEINTE D'IMPEDA
OPTICAL
RS-232C
IR
CONTROL
BD
IN
IN
1
IN
2
IN
3
OUT 1
OUT 2
ASSIGNABLE
3
1
-
ASSIGNABLE
(CD-R)
IN
4
(VIDEO1)
IN
3
(DVR)
IN
2
(TV/SAT)
IN
1
IN
3
(VIDEO 2)
IN
1
IN
IN
2
OUT
OUT
ZONE 2
OUT
VIDEO
ZONE 3
OUT
PHO
IN
L
R
SEE INSTRUCTION
MANUAL
SELECTABLE
VOIR LE MODE
D'EMPLOI
SELECTABLE
CONTROL
IN
OUT
CONTROL
IN
OUT
IN
OUT
CONTROL
SC-LX82_LX72.book Page 39 Thursday, April 23, 2009 7:05 PM