Pioneer SC-LX82 - Manual (Page 90)

Using other functions 09
90
En
2 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
3 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording
device and set the recording levels.
Refer to the instructions that came with the recorder if
you are unsure how to do this. Most video recorders set
the audio recording level automatically—check the
component’s instruction manual if you’re unsure.
4 Start recording, then start playback of the source
component.
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if you find
that the
OVER indicator lights often or you can hear
distortion in the sound. 1
SC-LX82:
SC-LX72:
• Set the remote control to the receiver operation
mode, then press A.ATT to switch the input attenuator
on or off.
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
SC-LX82:
SC-LX72:
• Set the remote control to the receiver operation
mode, then press SLEEP repeatedly to set the sleep
time.
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again. 2
Dimming the display
You can choose between four brightness levels for the
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
SC-LX82:
Note
1 The attenuator isn’t available with digital sources, or when using the Stream Direct (ANALOG DIRECT) modes.
SOURCE
TV RECEIVER
VOL
VOL
TVCONTROL
CH
RECEIVER
PGM MENU
S O
SIGNAL SEL SLEEP AUDIO
INFO
DIMMER
A.ATT SBch MCACC
HDMI OUT
D.ACCESS
ENTER
CLASS
DISP
CH
D C
A.ATT
INPUT
1 2 3
HDMI OUT
SLEEP MCACC
SELECT
SIGNAL SEL
4 5 6
DIMMER A.ATT SBch
7 8 9
CLASS
MASTER
VOLUME
CH LEVEL D.ACCESS
/CLR 0 ENTER
A.ATT
8
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
AUDIO
MULTI OPE
INFO
DISP
MPX PQLS
CH
RECEIVER TV CTRL
TV/DTV
RECEIVER
2 • You can also switch off the sleep timer simply by switching off the receiver.
• The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.
SOURCE
TV RECEIVER
VOL
VOL
TV CONTROL
CH
RECEIVER
THX PQLS MPX
PGM MENU
STEREO
SIGNAL SEL SLEEP AUDIO
INFO
DIMMER
A.ATT SBch MCACC
HDMI OUT
DISP
AUTO/ALC/
DIRECT STANDARD ADV SURR
SLEEP
1 2 3
HDMI OUT
SLEEP MCACC
INPUT
SELECT
SIGNAL SEL
4 5 6
DIMMER A.ATT SBch
7 8 9
CLASS
MASTER
CH LEVEL D.ACCESS
/CLR 0 ENTER
SLEEP
6
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
AUDIO
MULTI OPE
INFO
DISP
MPX PQLS
CH
RECEIVER TV CTRL
TV/DTV
RECEIVER
30 min 60 min
90 min Off
SOURCE
TV RECEIVER
VOL
VOL
TVCONTROL
CH
RECEIVER
THX PQLS MPX
PGM MENU
STEREO
SIGNAL SEL SLEEP AUDIO
INFO
DIMMER
A.ATT SBch MCACC
HDMI OUT
DISP
AUTO/ALC/
DIRECT STANDARD ADV SURR
DIMMER
SC-LX82_LX72.book Page 90 Thursday, April 23, 2009 7:05 PM