Pioneer SC-LX82 - Manual (Page 135)

Additional information 13
135
En
Remote control
HDMI
Symptom Remedy
Cannot be remote controlled. • SC-LX82 – Set the remote control mode properly (see Operating multiple receivers on page 93).
• SC-LX72 – Set a 5-digit preset code corresponding to the receiver to be operated in the remote
control (see Operating multiple receivers on page 100).
• Check whether the receiver’s remote control mode is properly set (see Remote Control Mode Setup
on page 127).
• Try replacing the batteries in the remote control (see Loading the batteries on page 10).
• Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel (see
Operating range of remote control unit on page 10).
• Check that there are no obstacles between the receiver and the remote control.
• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
• Check the connections of the CONTROL IN jack (see Operating other Pioneer components with this
unit’s sensor on page 39).
Other components can’t be
operated with the system
remote. • If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
• The preset code may be incorrect. Redo the procedure for entering preset codes.
Symptom Remedy
The HDMI indicator blinks
continuously. • Check all the points below.
No picture or sound. • This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-
compatible. If they are not, please connect them using the component, S-Video or composite video
jacks.
• Depending on the connected source component, it’s possible that it will not work with this receiver
(even if it is HDCP-compatible). In this case, connect using the component, S-Video or composite
video jacks between source and receiver.
• If the problem still persists when connecting your HDMI component directly to your monitor,
please consult the component or monitor manual or contact the manufacturer for support.
• If video images do not appear on your TV or flat screen TV, try adjusting the resolution, Deep Color
or other setting for your component.
• While analog video signals are being output over HDMI, use a separate connection for audio
output.
• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to
THROUGH, you cannot hear audio output from all channels. In this case, make a digital or analog
audio connection.
• To output signals in Deep Color, use an HDMI cable (High Speed HDMI™ Cable) to connect this
receiver to a component or TV with the Deep Color feature.
No picture. • Try changing the Resolution setting (in Setting the Video options on page 87).
• Set the HDMI output setting to the connected HDMI OUT terminal (in Switching the HDMI output
on page 91).
No sound, or sound suddenly
ceases. • Check that the HDMI AV setting is set to AMP/THROUGH.
• If the component is a DVI device, use a separate connection for the audio.
• If analog video is being output over HDMI, please use a separate connection for the audio.
• Check the audio output settings of the source component.
Noisy or distorted picture. • Sometimes a video deck may output a noisy video signal (during scanning, for example), or the
video quality may just be poor (with some video game units, for example). The picture quality may
also depend on the settings, etc. of your display device. Switch off the video converter and reconnect
the source and display device using the same type of connection (component, S-Video or
composite), then start playback again.
• If the problem still persists when connecting your HDMI component directly to your monitor,
please consult the component or monitor manual or contact the manufacturer for support.
HDCP ERROR shows in the
display. • Check whether or not the connected component is compatible with HDCP. If it is not compatible
with HDCP, reconnect the source device using a different type of connection (component, S-Video
or composite). Some components that are compatible with HDCP still cause this message to be
displayed, but so long as there is no problem with displaying video, this is not a malfunction.
SC-LX82_LX72.book Page 135 Thursday, April 23, 2009 7:05 PM