Metrohm 709 IC Pump - Manual (Page 70)

6 Appendix
709 IC Pump
62
Pump head 18
Components .....................................28
Disassemble .....................................27
Figure .............................................3,28
Maintenance .....................................27
Mounting ........................................8,30
Ordering designation........................53
Technical specifications ...................49
Pump stopped ......................................48
Purge valve 24
Connection to the pump head ........... 8
Deaerating the pump........................18
Figure .................................................. 3
Switching on/off ................................24
R
RAM initialization...................................35
RAM test................................................35
Rear......................................................... 2
Recorder output socket 34
Figure .................................................. 3
Technical data...................................49
Recycling...............................................25
Reduced flow rate.................................47
Remote control......................................50
Remote control commands..................42
Remote control language .....................37
Remote control via RS232 ....................37
Residual pulsation ................................49
RS232 interface 37
Baud rate...........................................43
Data transmission protocol ..............43
Error messages.................................41
Error rectification...............................41
Figure .................................................. 3
Handshake........................................43
Pin assignment .................................44
Remote control commands..............42
Status messages ..............................40
Switching...........................................23
Technical specifications ...................50
Trigger...............................................39
RS232 Test............................................34
Rules for remote control language .......38
S
Safety notes ............................................ 6
Safety rules.............................................. 6
Safety shutdown ..............................21,49
Safety specifications.............................51
Sapphire sleeve 76
Figure ................................................30
Sapphire sphere 77
Figure ................................................30
Sapphire supporting ring66
Figure ................................................28
Ordering designation........................55
Scope of delivery ..................................52
Screw 25
Figure .................................................. 3
Remove housing cover................45,46
Screw 26
Figure .................................................. 3
Remove housing cover................45,46
Screw 60
Figure................................................ 28
Tighten .............................................. 30
Undo ................................................. 27
Screw holder 70
Figure................................................ 28
Seal 79
Figure................................................ 30
Sealing ring 74
Figure................................................ 30
Sequence of operations ....................... 19
Service .................................................. 36
Servicing ............................................... 26
Setting the baud rate ............................ 45
Setting the flow rate .............................. 20
Setting up the pump............................... 7
Shutoff pressure
.......................see Pressure limit values
Sleeve 75
Figure................................................ 30
Sliding switch 35
Figure.................................................. 3
Sliding switch 36
Figure.................................................. 3
Switching .......................................... 23
SOP....................................................... 36
Special tool 71
Figure................................................ 28
Ordering designation........................ 52
Remove piston seal 67..................... 27
Special tool 72
Figure................................................ 28
Install piston seal 67......................... 29
Ordering designation........................ 52
Spilled chemicals.................................. 26
Spring 63
Figure................................................ 28
Ordering designations................. 55,56
Spring retainer 62
Figure................................................ 28
Srew holder 70
Tighten .............................................. 30
Standard Operating Procedures .......... 36
Static charges......................................... 6
Status messages .................................. 40
Steel capillary (6.2620.020) .................... 9
Steel capillary (6.2620.020) .................. 54
Steel connectors................................... 10
Steel mesh holding end 53
Figure................................................ 12
Mounting........................................... 12
Steel meshes 52
Figure................................................ 12
Mounting........................................... 12
Stirring of the eluent.............................. 25
Stop pump ............................................ 47
Storage ................................................. 51
Sunlight ................................................... 7
Switching on/off the instrument............ 17
Switching the pump drive on/off .......... 22
Syringe (6.2816.020) ............................ 18
Ordering designation........................ 53
T
Technical specifications ....................... 49
Test plug (3.496.8480) .................... 32,34
Transport ................................................ 7
Transport damage................................ 57
Transport safeguard block..................... 8
Treatment of eluents............................. 25
Trigger.............................................. 38,39
Tubing connections
Connection to eluent container........ 15
Connection to injection valve ...... 13,14
Tubule (6.2816.040)
Ordering designation ....................... 53
V
Validation .............................................. 36
Valve housing 73
Figure................................................ 30
W
Warning................................................... 5
Warranty................................................ 57
Z
Zircon piston (6.2824.070) .............. 27,55