Rice Lake BCi Belt Scale - Installation and Operation Manual Version 2.03 User Manual
Installation & operation manual
Advertising
Table of contents
Document Outline
- About This Manual
- Safety
- 1.0 Introduction and Overview
- 1.1 Belt Conveyor Scale System Components
- 1.2 Operation
- 1.3 Application Brief
- 1.4 Selecting a Mounting Location
- 1.4.1 Tension
- 1.4.2 Uniform Belt Loading
- 1.4.3 Single Load Point on Belt
- 1.4.4 Material Slippage
- 1.4.5 Convex Curves
- 1.4.6 Concave Curves
- 1.4.7 Trippers
- 1.4.8 Speed Sensor or Magnetic Shaft Encoder Mounting Location - (Optional items)
- 1.4.9 Electronic Wiring Location
- 1.4.10 Speed Wheel
- 1.4.11 Troughing Angle
- 1.5 Poor Choices for Belt Scale Installations
- 1.6 Handbook 44 Requirements for Belt Scales
- 2.0 Integrator Hardware Installation
- 3.0 Integrator Hardware Setup
- 4.0 Supervisor Mode Parameters
- 4.1 Admin. Passcode (numeric)
- 4.2 Scale Capacity
- 4.3 Load Cell MV
- 4.4 Total Load Cell Build
- 4.5 Rate Unit Time
- 4.6 Filter (s)
- 4.7 Filter Threshold (divisions)
- 4.8 Speed Unit Time
- 4.9 Fixed Speed
- 4.10 Unit of Measure
- 4.11 Unit of Rate
- 4.12 Rate Count By
- 4.13 Totalizer Count By
- 4.14 Load Display Units
- 4.15 Load Count By
- 4.16 Auto Zero Tracking Range (%)
- 4.17 Auto Zero Tracking Deviation (%)
- 4.18 Dead Band
- 4.19 Cal. Test Weight
- 4.20 Cal. Test Chain
- 4.21 Calibration Load
- 4.22 Material Factor
- 4.23 Span Error%
- 4.24 Zero Counts
- 4.25 Zero Error%
- 4.26 Idler Spacing
- 4.27 Number of Idlers
- 4.28 Belt Test Revolutions
- 4.29 Pulses per Revolution
- 4.30 Belt Length
- 4.31 Belt Angle
- 4.32 Pulses Per Unit Measure
- 4.33 Test Duration
- 4.34 Tons per Pulse (output)
- 4.35 Pulse Duty Cycle (in seconds)
- 4.36 Low Rate Alarm Value (%)
- 4.37 Maximum Speed Value
- 4.38 Low Rate Alarm Bit
- 4.39 High Rate Alarm Bit
- 4.40 Speed Alarm Bit
- 4.41 Totalizer Pulse Bit
- 4.42 Fill Output Bit
- 4.43 Remote Print Input Bit
- 4.44 Print Output Port
- 4.45 Print Format
- 4.46 Stream Output Port
- 4.47 Stream Format
- 4.48 Clear Totalizer with Print
- 4.49 Remote Totalizer Reset Input
- 4.50 Integrator Identification
- 4.51 Preact Length
- 4.52 Enable Batching
- 4.53 Analog 1 Mode
- 4.54 Analog 2 Mode
- 4.55 Master Totalizer Reset
- 4.56 Interfacing a PLC to the Belt Scale System
- 4.57 Special Serial Commands
- 5.0 Calibration
- 6.0 Run Sequence
- 7.0 Handbook 44 Requirements for Belt-Conveyor Scales
- 8.0 Maintenance
- 9.0 Appendix
- Integrator Limited Warranty