Kenwood UD-900M - Manual (Page 82)

Specifications (For U.S.A. and Canada)
Pre Amplifier / Tuner unit (C-A9)
FM Tuner section!
Tuning frequency range................ 87.5 MHz - 108 MHz
Sensitivity (IHF)....................... 12.8 dBf (1.2 |xV at 75 Q)
Total harmonic distortion at 1 kHz
MONO................................................................. 0.5%
STEREO...............................................................0.6 %
Signal to noise ratio at 1 kHz
MONO........................................80 dB (85 dBf input}
STEREO....................................74 dB (85 dBf input)
Selectivity (IHF ± 400 kHz)....................................... 50 dB
Stereo separation (IHF at 1 kHz).......................... . 40 dB
Frequency response... 30 Hz ~ 15 kHz + 0.5 dB, - 3 dB
I AM Tuner section~1
Tuning frequency range................. 530 kHz ~ 1,700 kHz
Usable sensitivity......................... 10 ]aV / (500 [iV / m)
Signal to noise ratio.................................................48 dB
I Pre Amplifier section |
Rated output voltage (PRE OUT)
................................ . 1.0 V (40 Hz - 20 kHz, 0.02 %)
Total harmonic distortion
.............................................0.02 % (40 Hz - 20 kHz)
..................................... ...................... 0.01 % (1 kHz)
Signal to noise ratio... 90 dB (IHF'66) / 85 dB (IHF'78)
Input sensitivity / Impedance
MD / DAT, LD / AUX, VIDEO............ 200 mV / 47 kQ
MIC.................... .................................1.2 mV/47 kQ
Loudness control
VOLUME at -30 dB level................... + 6 dB (100 Hz)
N.B. circuit (- 30 dB Volume level).......................+ 12 dB
(at 60 Hz)
Output level / Impedance
MD / DAT, VIDEO............ ................ 200 mV / 2.2 k Q .
Graphic equalizer
Individual channel................60 Hz, 150 Hz, 400 Hz,
1 kHz, 2.5 kHz, 6 kHz, 15 kHz
I VIDEO section]
Input level / Impedance
VIDEO (composite)...............................1 Vp-p / 75 Q
Input (LD / AUX,VIDEO IN)
Output level / Impedance
VIDEO (composite).......................... . 1 Vp-p / 75
Output (MONITOR OUT,VIDEO OUT)
[General]
Dimensions............................... W: 270 mm (10-5 / 8")
H: 85 mm (3-3 / 8")
D: 318 mm (12-1 /2")
Weight (net)............................... ................. 3.1 kg (6.8 lb)
Power Amplifier unit (B-A9)
Rated power output
35 watts per channel minimum RMS, both chan­
nels driven, at 4 n from 40 Hz to 20 kHz with no
more than 0.06 % total harmonic distortion
Presence 1 kHz at 8 ............................... 20 W + 20 W
Total harmonic distortion
......................... 0.06 % (40 Hz - 20 kHz, 35 W, 4 Q)
................ 0.005 % (1 kHz, 1/2 Rated power, 4 Q)
Frequency response
......................... . 40 Hz ~ 70 kHz, + 0 dB, - 1.5 dB
Signal to noise ratio
.............................. 105 dB (IHF'66) / 90 dB (IHF'78)
[General]
Power consumption ...............................................170 W
Dimensions................................. W: 270 mm (10-5 / 8")
H: 120 mm (4-3/4")
D: 317 mm (12-1/2")
Weight (net).............................................. 6.4 kg (14.1 lb)
Note:
KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
For the U.S.A.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may
cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. Fiowever, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer­
ence by one or more of the following measures:
- - Reorient or relocate the receiving anténna.
- - Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- - Consult the dealer or an experienced radio / TV technician for help.
82 u D-900/UD-9D0M (En)