Altera Transceiver Signal Integrity Development Kit, Stratix IV GX Edition - Manual (Page 15)

Chapter 2: Board Components 2–5
Board Overview
November 2011 Altera Corporation Transceiver Signal Integrity Development Kit,
Stratix IV GX Edition Reference Manual
J31, J33 GXB2 transmit channel 7 Transceiver GXB2 transmit channel 7 connected to SMA.
J35, J37 GXB2 receive channel 7 Transceiver GXB2 receive channel 7 connected to SMA.
J12 Fan power connector Power connector for 5-V DC fan sink.
J64 Fan control jumper
Jumper to select whether the fan is always on or automatically
controlled by the FPGA.
SW8 Reset push button Board reset push button.
SW9 CPU reset push button CPU reset push button.
Power
J1 Power Input Jack
14-V – 20-V DC female input power jack. Accepts 2.5-mm male
center-positive barrel from supplied 16-V DC power supply.
SW1 Power switch Switch to power on/off the board.
J2 0.9-V banana jack
Banana jack for supplying external 0.9-V V
CC
power to the FPGA. Fuses
F1 and F2 must be removed prior to supplying external power to this
banana jack.
J3 VCCA banana jack
Banana jack for supplying external V
CCA
power to the FPGA. Fuse F3
must be removed prior to supplying external power to this banana jack.
J7 VCCR and VCCT banana jack
Banana jack for supplying external V
CCR
and V
CCT
power to the FPGA.
Fuse F84 must be removed prior to supplying external power to this
banana jack.
J9 VCCH banana jack
Banana jack for supplying external V
CCH
power to the FPGA. Fuse F6
must be removed prior to supplying external power to this banana jack.
J10 VCCL banana jack
Banana jack for supplying external V
CCL
power to the FPGA. Fuse F7
must be removed prior to supplying external power to this banana jack.
J4, J5 GND banana jack Banana jack connected to GND of the board.
F1, F2 10A fuse
Fuses for 0.9-V V
CC
core of the FPGA. These fuses must be removed
when an external power is applied to this banana jack.
F3 2A fuse
Fuse for V
CCA
power of the FPGA. This fuse must be removed when an
external power is applied to this banana jack.
F6 5A fuse
Fuse for V
CCH
power of the FPGA. This fuse must be removed when an
external power is applied to this banana jack.
F7 2A fuse
Fuse for V
CCL
power of the FPGA. This fuse must be removed when an
external power is applied to this banana jack.
F84 5A fuse
Fuse for V
CCR
and V
CCT
power of the FPGA. This fuse must be removed
when an external power is applied to this banana jack.
U14 Power measurement ADC
Linear Technology LTC2418CGN 24-bit delta-sigma analog to digital
converter (ADC).
R3 0.001- Ω Rsense Sense resistor for measuring FPGA V
CC
core power.
R11 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCA
power.
R24 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCH
power.
R25 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCL
power.
R20 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCR
and V
CCT
combined power.
Note to Table 2–1 :
(1) Information for the board reference whose components on the engineering silicon board differ from the production silicon board are listed in
Table A–2 on page A–2 .
Table 2–1. Stratix IV GX Transceiver Signal Integrity Development Board Components (Part 4 of 4) (1)
Board Reference Type Description