Interspace Industries TheatreCue 16 Way V4 System - 16 Outstations - Manual (Page 16)

Designed and created by:-
Built By
The following options can be programmed
individually for each channel from the Master Station.
To change any of these settings, see the Master Station
Configuration Editor on page 34.
Outstation
S/by colour
S/by Flash on
S/by Flash on
S/by latches
S/by Dim on ACK
Go Flickers
Go times out
Go flashes
Go latches
Go & S/by interlocked
Call LED enabled
Call LED Flashes
ACK button backlight
Beeper (QLS-B only)
Beep on Go (QLS-B only)
Dimmer
Outstation
Master
Factory
Default
Yellow
Flashes
Flashes
Latches
No
Steady
Times out
Flashes
Latches
Interlocked
Enabled
Flashes
On
Enabled
Silent
100% Red
Steady
Steady
Momentary
Dims on ACK
Flickers
Stays on
Steady
Momentary
Independent
Call LED off
Steady
Off
Disabled
Beeps on Go
5-100% 5 steps:
User Selectable
Option
Option
Cue Light Outstations (Continued)
These 16 options can be combined in 48,152 different ways
for each channel. Hopefully there is a combination that suits
any special applications that may arise. Please let us know
if there are any options that you would like but are not
provided.
•
•
Selectable between red and yellow (default).
Default setting is to flash.
Some users prefer a non-flashing standby lamp.
The Outstation’s standby lamp can be set to flash or not
independently of the standby lamp on the Master Station.
To indicate an acknowledged cue on the Outstation, the
Outstation can be set to DIM on Confirm if required.
Standby Flash on Outstation
Standby Colour
•
Default setting is to flash.
If the Outstation’s standby lamp is set to not flash, it is
desirable to have the Master Station’s lamp flash so that an
indication of a Confirm cue can be seen.
Some applications use the Outstations to indicate a
safe/unsafe condition. In this situation the Standby lamps on
both the Master Station and Outstation are set to not flash.
Default setting is to latch.
If set to unlatched (momentary action), the Standby lamp will
only be lit for as long as the Master Station’s Standby button
is pressed.
Default setting is not to dim.
When an Outstation’s Standby lamp is set to not flash, the
Outstation can be set to dim its Standby lamp to indicate a
confirm cue.
Default setting is not to flicker.
As an aid for colour blind users, the Go lamp can be set to
flicker instead of burning steadily.
The flicker rate is approximately 30Hz.
Default setting is to time out after 15 seconds.
Once a Go button on the Master Station has been pressed,
the cue will cancel itself after 15 seconds allowing the stage
manager to attend to other duties. It can be set to not time
out and will stay on until either the Go or Standby button is
pressed.
Default setting is to flash.
Once a Go button on the Master Station has been pressed,
the Go lamp will initially burn steadily but will flash after 3
seconds. It can be set to not flash and will burn steadily until
it times out or is cancelled.
Standby Flash on Master Station
•
•
•
•
•
Standby Latches
Standby Dim on Confirm
Go lamp flickers
Go lamp times out
Go lamp flashes
16.
Cue Light options for the following Outstation types:
Standard (QLSi2), Beeper (QLSi2-B).
Beeper and Beep-On-Go options only apply when a Beeper
Outstation (QLSi2-B) is connected to that channel. Outstations
without a beeper ignore the beeper settings.