H3C Technologies H3C S7500E Series Switches User Manual
Page 103
7-32
[DeviceB] rrpp enable
3) Configuration on Device C
# Create VLANs 1 and 2, map VLAN 1 to MSTI 1 and VLAN 2 to MSTI 2, and activate MST
region configuration.
<DeviceC> system-view
[DeviceC] vlan 1 to 2
[DeviceC] stp region-configuration
[DeviceC-mst-region] instance 1 vlan 1
[DeviceC-mst-region] instance 2 vlan 2
[DeviceC-mst-region] active region-configuration
[DeviceC-mst-region] quit
# Set the physical state change suppression interval on GigabitEthernet2/0/1 and
GigabitEthernet2/0/2 to 0 seconds, disable STP, configure the two ports as trunk ports, and
assign them to VLAN 1 and VLAN 2.
[DeviceC] interface gigabitethernet 2/0/1
[DeviceC-GigabitEthernet2/0/1] link-delay 0
[DeviceC-GigabitEthernet2/0/1] undo stp enable
[DeviceC-GigabitEthernet2/0/1] port link-type trunk
[DeviceC-GigabitEthernet2/0/1] port trunk permit vlan 1 2
[DeviceC-GigabitEthernet2/0/1] quit
[DeviceC] interface gigabitethernet 2/0/2
[DeviceC-GigabitEthernet2/0/2] link-delay 0
[DeviceC-GigabitEthernet2/0/2] undo stp enable
[DeviceC-GigabitEthernet2/0/2] port link-type trunk
[DeviceC-GigabitEthernet2/0/2] port trunk permit vlan 1 2
[DeviceC-GigabitEthernet2/0/2] quit
# Set the physical state change suppression interval on GigabitEthernet2/0/3 to 0 seconds,
disable STP, configure the port as a trunk port, and assign it to VLAN 2.
[DeviceC] interface gigabitethernet 2/0/3
[DeviceC-GigabitEthernet2/0/3] link-delay 0
[DeviceC-GigabitEthernet2/0/3] undo stp enable
[DeviceC-GigabitEthernet2/0/3] port link-type trunk
[DeviceC-GigabitEthernet2/0/3] port trunk permit vlan 2
[DeviceC-GigabitEthernet2/0/3] quit
# Set the physical state change suppression interval on GigabitEthernet2/0/4 to 0 seconds,
disable STP, configure the port as a trunk port, and assign it to VLAN 1.
[DeviceC] interface gigabitethernet 2/0/4
[DeviceC-GigabitEthernet2/0/4] link-delay 0
[DeviceC-GigabitEthernet2/0/4] undo stp enable
[DeviceC-GigabitEthernet2/0/4] port link-type trunk
[DeviceC-GigabitEthernet2/0/4] port trunk permit vlan 1
[DeviceC-GigabitEthernet2/0/4] quit
# Create RRPP domain 1, configure VLAN 10 as the primary control VLAN of RRPP domain 1,
and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.
[DeviceC] rrpp domain 1
[DeviceC-rrpp-domain1] control-vlan 100
[DeviceC-rrpp-domain1] protected-vlan reference-instance 1