Document Outline

• 1.0 Introduction
  • 1.1 Equipment Inspection
  • 1.2 Outside Enclosure Overview
    • Figure 1 Small enclosure—external features
    • Figure 2 Large enclosure—internal features
  • 1.3 Typical Sequence
    • Figure 3 Example of typical sequence: Analog input reaches high setpoint
  • 1.4 Controller Board Overview
    • Table 1 Controller board components
  • 1.5 LED Indicators
    • Table 2 LED indicators summary
• 2.0 Installation
  • 2.1 Installation Considerations
    • 2.1.1 Unpacking and Preliminary Inspection
      • Packing Contents
        • Table 3 Packing manifest
  • 2.2 Surface-Mounting the Liquitect Panel
    • Required tools
    • 2.2.1 Mounting the Panel
      • Figure 4 Mounting dimensions
  • 2.3 Flush-Mounting the Liquitect Panel
    • Required tools
    • 2.3.1 Mounting the Panel
  • 2.4 Connect Power to the Liquitect Panel
    • 2.4.1 Input Power Connections - Small Enclosure
      • Figure 5 Electrical connections to panel
    • 2.4.2 Input and Output Power Connections - Large Enclosure
      • Input Power Connections
      • 24 VAC Output Power Connections
        • Figure 6 Power wiring to TM115
        • Figure 7 Power wiring to TM230
      • Troubleshooting - Transformer Module
• 3.0 Connections and Configuration
  • Table 4 Wiring specifications
  • 3.1 Connecting Leak Detection Cable Inputs
    • 3.1.1 Attaching Leak Detection Connection Cable to the Panel
    • 3.1.2 Connecting Leak Detection Cable to the Connection Cable
      • Figure 8 Fittings on leak detection cable (LT500Y) and connection cable (CONNECT10)
      • Figure 9 Typical leak detection cable layout
      • Figure 10 Installation of hold- down clips in pairs
      • Figure 11 Cable laid in straight patterns
      • Figure 12 Cable laid in circular patterns
      • Figure 13 90˚ turn in cable
  • 3.2 Connecting Alarm Outputs
  • 3.3 Connecting to a Building Maintenance System or External Alarm System
  • 3.4 RS422 SiteScan Web Connector
  • 3.5 Disable the Audible Horn
• 4.0 Overview of Menus
  • 4.1 View Status Overview
  • 4.2 System and Control Overview
    • Figure 14 Menu overview
• 5.0 View Status Options
  • Figure 15 Menu overview - View Status menu
  • 5.1 View Cable Status
    • 5.1.1 Cable Status Screens
      • Viewing Additional Screens
      • Overall Condition
        • Table 5 Overall cable conditions
      • Cable Length & Current Value
  • 5.2 View Alarm History
    • 5.2.1 Alarm History Log
      • Table 6 Alarm History Log conditions
      • Viewing Additional Screens
  • 5.3 View Zone Trend
    • 5.3.1 Zone Trend Log
      • Viewing Additional Screens
• 6.0 System and Control Options
  • Table 7 Valid characters for data entry
  • 6.1 Login
    • Figure 16 Menu overview - System and Control menu
  • 6.2 Setup System - Overview
  • 6.3 Setup System - Setup ZN1 Zone 1
    • Table 8 Default settings - Zone 1
    • 6.3.1 Identify the Zone as Connected
    • 6.3.2 Change Zone Label
    • 6.3.3 Change Units Label
    • 6.3.4 Auto Calibration
    • 6.3.5 Set Up Sensitivity for Water Detection
    • 6.3.6 Set Up Sensitivity for Contamination Detection
  • 6.4 Setup System - Setup ZN2 Zone 2
  • 6.5 Setup System - Setup Alarm Outputs
    • Table 9 Default settings - alarm outputs
    • 6.5.1 Specify Longest Cable Length
      • Table 10 Operation of 420mA outputs
    • 6.5.2 Define Relays as Normally Open or Normally Closed
    • 6.5.3 Define Alarms as Latched or Unlatched
      • Liquitect System’s Response to Alarms - Both Latched and Unlatched
      • Latched Alarms Only
      • Unlatched Alarms Only
  • 6.6 Setup System - Setup Re-Alarm Delay
  • 6.7 Setup System - Setup Mapmode
    • Table 11 Default mapping values
    • 6.7.1 View Last Map
  • 6.8 Setup System - Setup System Info
    • 6.8.1 Change Password
      • Change the Password
      • Reset Password to the Factory Default (“AAAA”)
    • 6.8.2 Change Date & Time/Automatic Daylight Saving Time
    • 6.8.3 Factory Defaults
      • Table 12 Factory default settings
  • 6.9 Reset Latched Alarms
  • 6.10 Clear Alarm History
  • 6.11 Clear Zone Trend
• 7.0 Specifications
  • 7.1 Liquitect Panel Specifications