Invacare 9000 XT - Manual (Page 41)

Part No. 1056953 41 9000 Series
SECTION 8 ANTI-TIPPERS/WHEEL LOCKS
ANTI-TIPPERS/WHEEL
LOCKS
ADJUSTING (FIGURE 2)
1. Press the release buttons on the wheeled
portion of the anti-tipper and slide it up or
down to achieve the 1-1/2 to 2-inch clearance.
2. Check to make sure that the release buttons
are fully engaged in adjustment holes.
NOTE: Refer to the following charts to ensure
the correct anti-tipper is installed in the wheel-
chair. Seat-to-Floor heights are approximate de-
pending on front caster size and type. Anti-Tip-
per length measurement is taken with the ex-
tension tube in the longest position available.The
anti-tipper height measurement MUST be taken
with the anti-tipper on a flat surface.
Anti-Tipper Length
Flat Surface
Anti-Tipper
Height
9000 XT WITH 3° SEAT-TO-FLOOR ANGLE AND 9000 SL (ADULT/HEMI FRAMES)
CASTER SEAT-TO-FLOOR ANTI-TIPPER ON CHAIR OFF CHAIR
SIZE HEIGHT LENGTH / HEIGHT KIT NUMBER
8-inch 17-1/2,18-1/2,19-1/2-inches 13-1/2 / 3-1/2-inches 1360 1058836
6-inch 15-1/2,16-1/2,17-1/2-inches 11-5/8 / 2-3/4-inches 1360A 1058752
9000 XT WITH 6° SEAT-TO-FLOOR ANGLE (ADULT/HEMI FRAME)
CASTER SEAT-TO-FLOOR ANTI-TIPPER ON CHAIR OFF CHAIR
SIZE HEIGHT LENGTH / HEIGHT KIT NUMBER
8-inch 17-1/2,18-1/2,19-1/2-inches 13-1/2 / 2-7/8-inches N/A 1113766
6-inch 16-1/2,17-1/2-inches 12-1/2 / 2-3/4-inches N/A 1113765
15-1/2-inches 9-1/2 / 2-3/8-inches N/A 1113764
9000 XT WITH 0° SEAT-TO-FLOOR ANGLE (ADULT/HEMI FRAME)
CASTER SEAT-TO-FLOOR ANTI-TIPPER ON CHAIR OFF CHAIR
SIZE HEIGHT LENGTH / HEIGHT KIT NUMBER
8-inch 17-1/2,18-1/2-inches 13-1/2 / 3-1/2-inches N/A 1058836
6-inch 16-1/2,17-1/2-inches 13-1/2 / 3-1/2-inches N/A 1058836
15-1/2-inches 11-5/8 / 2-3/4-inches N/A 1058752
9000 XT (SUPER LOW FRAME)
CASTER SEAT-TO-FLOOR ANTI-TIPPER ON CHAIR OFF CHAIR
SIZE HEIGHT LENGTH / HEIGHT KIT NUMBER
6-inch 13-1/2 and 14-1/2-inches 10-1/2 / 2-inches 1360SH 1064520
9000 XDT (ADULT TALL FRAME)
CASTER SEAT-TO-FLOOR ANTI-TIPPER ON CHAIR OFF CHAIR
SIZE HEIGHT LENGTH / HEIGHT KIT NUMBER
8-inch 17-1/2 and 19-1/2-inches 11-5/8 / 2-3/4-inches 1360A 1058752
8-inch 21-1/2-inches 13-1/2 / 3-1/2-inches 1360 1058836
1-1/2 to 2-inch Clearance
FIGURE 2 - ADJUSTING THE
ANTI-TIPPERS
Release Buttons