JVC VR-509E - Manual (Page 120)

RS-232C Interface
120
• SET (40H) [BASIC/JVC-1]
See ENTER (40H) on page125.
• DOWN (63H) [JVC-1]
• RIGHT (64H) [JVC-1]
• LEFT (68H) [JVC-1]
• UP (69H) [JVC-1]
Shifts the parameter settings when the timer PRG and the
alarm search parameters have been set.
Shifts the selection fields with the [UP] and [DOWN] when
the menu is being displayed.
• Vol +, – (65H, 66H) [JVC-1]
Changes the set values with + (ascending) and –
(descending).
• SEQ (6AH) [JVC-1]
Changes the monitor output screen mode.
• MENU ON (6BH) [JVC-1]
Displays the menu.
• MENU OFF (6CH) [JVC-1]
Clears the menu.
• MENU ON/OFF (6DH) [JVC-1]
Switches between menu displays/clear.
• ON SCREEN SELECT (74H) [JVC-1]
Switches the contents displayed on screen. (REMAIN
display is not performed when repeat recording is set at
ON.)
• CANCEL (76H) [JVC-1]
Cancels the program data on the program timer setup
screen.
• HDR PB CAMERA SET (86H) [JVC-1]
Specifies the playback camera. The monitor output camera
is specified during recording.
The camera that outputs images to SPOT output is
specified when in the [SPOT OUTPUT] mode.
* FULL size sequential display, QUAD sequential display
and 6 WAY specification are invalidated when in the
playback mode (include when recording and playback
are performed at the same time).
* The FULL size sequential display
⇔ QUAD sequential
display specifications are invalid.
* Invalid with Second Byte: FULL size sequential display,
QUAD sequential display, 6 WAY screen and 9 WAY
specifications.
• DATE SET(8EH) [BASIC/JVC-1]
Sets the month, day and year in the VR-509.
(Cannot be set when the NTP Client function is enabled, or
when the VR-509 is in the recording mode.)
• TIME SET(8FH) [BASIC/JVC-1]
Sets the hours, minutes and seconds in the VR-509.
(Cannot be set when the NTP Client function is enabled, or
when the VR-509 is in the recording mode.)
• MENU RESET (EFH) [JVC-1]
Initializes the menu setup values.
(Cannot be set when the VR-509 is in the recording mode,
or when the operation lock has been activated.)
3. Details of the Commands (continued)
3.3. Setup Commands
74H
1st byte 2nd byte
0AH
TXD
RXD 0AH
Second byte
Bit Status Detail
7 1 / 0 REC TO STOP MESSAGE : 1( ON ) / 0( OFF )
6 1 / 0 WARNING : 1( ON ) / 0( OFF )
5 1 / 0 CAMERA TITLE : 1( ON ) / 0( OFF )
4 1 / 0 PLAYBACK : 1( ON ) / 0( OFF )
3 1 / 0 DISK CAPACITY : 1( ON ) / 0( OFF )
2 1 / 0 ALARM DETECT : 1( ON ) / 0( OFF )
1 1 / 0 ALARM COUNT : 1( ON ) / 0( OFF )
0 1 / 0 DATE/TIME : 1( ON ) / 0( OFF )
86H
1st byte 2nd byte
0AH
TXD
RXD 0AH
3rd byte
0AH
Second byte
Bit Status Detail
7 to 4 Fixed at “3”
0 / 1 / 2
3 to 0 3 / 4 / 5
6
0: FULL size specification / 1: FULL size sequential display
2: QUAD specification / 3: QUAD sequential display
5: 6 WAY specification / 6: 9 WAY specification
Third byte
Bit Status Detail
7 to 4 Fixed at “3”
3 to 0 8 to 0
Second BYTE: During FULL size specification
8: Camera 9 specification to 0: Camera 1 specification
Second BYTE: During QUAD specification
2: QUAD-C
1: QUAD-B
0: QUAD-A
Values that do not correspond to each setting are
invalidated.
8EH
0AH
TXD
RXD 0AH
Month Day Year
0AH 0AH 0AH 0AH 0AH
8FH
0AH
TXD
RXD 0AH
Hours Minutes Seconds
0AH 0AH 0AH 0AH 0AH