Yokogawa EJA118 - Manual (Page 33)

IM 1C22H1-01E 7-4
7. BRAIN TERMINAL BT200 OPERATION
7.3 Setting Parameters Using the BT200
7.3.1 Parameter Summary
Instruments to which applicable:
F: Differential pressure transmitters
EJA110, EJA120, EJA118W, EJA118N, EJA118Y, and EJA115
P: Pressure transmitters EJA310, EJA430, EJA438W, and EJA438N
L: Liquid level transmitters EJA210 and EJA220
No. Description
Model+capsule type
Tag number
Applica-
bility
P L F
01
02
T0705.EPS
Rewrita-
bility
16 alphanumerics
GOOD/ERROR
Remarks Item
MODEL
TAG NO.
Self-diagnostic result
—
—
—
03 SELF CHECK
Measured data display A
–5 to 110%
Menu name DISPLAY
Output (in %) A10 OUTPUT (%)
–19999 to 19999 Output (in engineering
units) A11 ENGR.
OUTPUT
Unit specified in D30 Amplifier temperature A20 AMP TEMP
Unit specified in D30 Capsule temperature A21 CAPSULE
TEMP
—
Sensor type B
16 uppercase alphanumerics
Menu name SENSOR
TYPE
Model+span B10 MODEL
—
Style number B11 STYLE NO.
–32000 to 32000 Lower range-limit B20 LRL
–32000 to 32000 Upper range-limit B21 URL
–32000 to 32000 Minimum span B30 MIN SPAN
—
—
—
—
—
Unit specified in D31* Static pressure A30 STATIC
PRESS
–32000 to 32000 Input (indicated in
engineering DP unit) A40 INPUT
GOOD/ERROR, CAP MODULE
FAULT, AMP MODULE FAULT,
OUT OF RANGE, OUT OF SP
RANGE*, OVER TEMP (CAP),
OVER TEMP (AMP),
OVER OUTPUT, OVER DISPLAY,
ILLEGAL LRV, ILLEGAL HRV,
ILLEGAL SPAN, and
ZERO ADJ OVER Self-diagnostic
messages A60 SELF CHECK
—
—
—
—
—
—
—
* In case of Model EJA120, static pressure cannot be measured. The display is always 0 MPa, but
this is not a measured value.
Maximum atatic
pressure B40
Same as A60
MAX STAT.P.
Self-diagnostic
messages
—
—
B60 SELF CHECK
Setting data C
16 alphanumerics
Menu name SETTING
Tag number C10 TAG. NO.
Selected from mmH
2
O, mmAq,
mmWG, mmHg, Torr, Pa, hPa, kPa,
MPa, mbar, bar, gf/cm
2 , kgf/cm 2 ,
inH
2
O, inHg, ftH
2
O, psi, or atm
Measurement range
units C20 PRESS UNIT
–32000 to 32000(but within
measurement range) Measurement range,
lower range value C21 LOW RANGE
—
Self-diagnostic
messages C60 Same as A60 SELF CHECK
—
—
—
—
–32000 to 32000(but within
measurement range) Measurement range,
higher range value C22 HIGH
RANGE
Selected from 0.2, 0.5, 1.0, 2.0,
4.0, 8.0, 16.0, 32.0, or 64.0 sec. Damping time constant C30 AMP
DAMPING
Selected from OUT:LIN; DSP:LIN,
OUT:LIN; DSP:SQR,
OUT:SQR; DSP:SQR Output mode and
integral indicator mode C40 OUTPUT
MODE
0.0 to 20.0%
LINEAR/ZERO Low cut D10 LOW CUT
Low cut mode D11 LOW CUT
MODE
NORMAL %/USER SET,
USER & %/INP PRES, PRES & % Display selection D20 DISP SELECT
—
Auxiliary setting data 1 D Menu name AUX SET 1
—
Default Value
As specified when ordered.
As specified when ordered.
As specified when ordered.
As specified when ordered.
2 s
As specified when ordered.
If not specified,
OUT: LIN; DSP: LIN.