Document Outline

• SAFETY INSTRUCTIONS
  • Safety Symbols
  • Safety Guidelines
  • Power cord for the United Kingdom
• GETTING STARTED
  • GSP-930 Introduction
    • Main Features
  • Accessories
    • Package Contents
  • Appearance
    • GSP-930 Front Panel
    • Rear Panel
    • Display
    • Status Icon Overview
  • First Use Instructions
    • Tilting the Stand
    • Inserting the Battery Pack
    • Power UP
    • Power Down
    • Setting the Date, Time and Wake-Up Clock
    • Firmware Update
    • Restoring Default Settings
    • Conventions
• BASIC OPERATION
  • Frequency Settings
    • Center Frequency
    • Start and Stop Frequency
    • Center Frequency Step
    • Frequency Offset
  • Span Settings
    • Span
    • Full Span
    • Zero Span
    • Last Span
  • Amplitude Settings
    • Reference Level
    • Attenuation
    • Scale/Div
    • Scale Type
    • View Scale
    • Vertical Scale Units
    • Reference Level Offset
    • Amplitude Correction
      • Create a Correction Set
      • Amplitude Correction On/Off
      • Delete Correction Set
      • Save Correction Set To Memory
      • Recall Correction Set From Memory
    • Input Impedance
    • Input Impedance Calibration
    • Using the Built-in Pre-Amplifier
  • Autoset
    • Using Autoset
    • Limiting the Autoset Vertical Search Range
    • Limiting the Autoset Horizontal Search Range
  • Bandwidth/Average Settings
    • Resolution Bandwidth Setting (RBW)
    • Video Bandwidth Settings (VBW)
    • VBW/RBW Ratio
    • Average Trace
    • Average Type
    • EMI Filter
  • Sweep
    • Sweep Time
    • Single Sweep
    • Continuous Sweep
    • Gated Sweep Overview
    • Using the Gated Sweep Mode
  • Trace
    • Selecting a Trace
    • Trace Math
    • Trace Detection Mode
  • Trigger
    • Selecting a Trigger Type
      • Free Run Mode
      • Activate Video Trigger
      • Activate External Trigger
    • Selecting the Trigger Mode
    • Set the Trigger Delay Time
  • Marker
    • Activating a Marker
      • Activate a Normal Marker
      • Move Marker Manually
      • Move Marker to Preset Locations
      • Activate Delta Marker
      • Move Delta Marker(s)Manually
    • Marker Functions
      • Marker Noise
      • Frequency Counter
    • Move Marker to Trace
    • Show Markers in Table
    • Peak Search
      • Move Marker to Peak
      • Move Marker and Peak to Center
      • Search for Peaks
      • Peak Configuration
    • Peak Table
  • Display
    • Adjusting the LCD Brightness
    • Turning the LCD Backlight Off
    • Setting a Display Line (Reference Level Line)
    • Using the Video Out Port
    • Setting the Display Mode
    • Split Spectrum View
  • System Settings
    • System Information
    • Error Messages
    • Set the System Language
    • Set the Date and Time
    • Using the Wake-Up Clock
    • Alarm Output
  • Preset
    • Using the Preset Key
    • Save the User Preset Settings
    • Preset Type Settings
    • Power on Preset Settings
• ADVANCED OPERATION
  • Measurement
    • Channel Analysis Overview
      • ACPR
      • OCBW
    • AM/FM Analysis
      • AM Analysis
      • FM Analysis
      • AM/FM Demodulation
    • N dB Bandwidth
    • Phase Jitter Measurement
    • Spectrum Emission Mask Overview
    • Spectrum Emission Mask Testing
    • Third Order Intermodulation Distortion (TOI)
    • CNR/CSO/CTB Measurement
      • Carrier to Noise Ratio (CNR)
      • Composite Second Order (CSO)
      • Composite Triple Beat (CTB)
  • Limit Line Testing
    • Creating a Limit (Point by Point)
    • Creating a Limit (from Trace Data)
    • Creating a Limit (from marker data)
      • Delete Limit Line
      • Pass Fail Testing
  • Sequence
    • Editing a Sequence
    • Running a Sequence
  • Tracking Generator
    • Activate Tracking Generator
    • Normalize the Tracking Generator
  • Power Meter
    • Activating Power Meter Mode
    • Data Logging Power Meter Measurements
• FILE
  • File Overview
    • File Type Overview
    • File Types
    • Using the File Explorer
    • Copy Files
    • Move Files
    • Delete Files
    • Rename Files
    • Save Files
    • Recall Files
    • Quick Save
• REMOTE CONTROL
  • Interface Configuration
    • Configure to USB Remote Interface
    • Configure GPIB Interface
    • Configure the LAN and LXI Interface
    • Configure RS232C
    • RS232C Remote Control Function Check
    • LXI Browser Interface and Function Check
    • GPIB/LAN Control Function Check
• FAQ
  • I connected the signal but it does not appear on screen.
  • I want to see which optional items are installed.
  • The performance does not match the specification.
• APPENDIX
  • Replace the Clock Battery
  • Glossary of Acronyms
  • GSP-930 Default Settings
  • Menu Tree
    • Amplitude
    • Frequency, Span, Autoset, BW Avg, Sweep
    • Limit Line
    • Trigger, Sequence
    • Trace, Display
    • Marker
    • Peak Search, Marker->
    • System
    • Mode, File
    • Save
    • Recall
    • Measure
  • GSP-930 Specifications
    • Frequency
    • Amplitude
    • Sweep
    • RF Preamplifier
    • Front Panel Input/Output
    • Rear Panel Input/Output
    • General
    • Tracking Generator (Optional)
    • USB Power Sensor (Optional)
  • GSP-930 Dimensions
• INDEX