Kinze 4900 Front Folding Planter Rev. 5/14 - Manual (Page 91)

TM
Model 4900 M0247-01
Rev. 5/14 6-9
Lubrication and Maintenance
GRADE 2
No Marks
GRADE 5
3 Marks
GRADE 8
6 Marks
TORqUE VALUES- ALUMINUM
Diameter Torque Value
⅛ " 180-220 in-lb
⅜ " 350-380 in-lb
½ " 350-400 in-lb
¾ " 350-400 in-lb
NOTE: Use these torque values with
pneumatic down pressure components.
MOUNTING bOLTS AND HARDWARE
Before operating planter for the first time, check all hardware is tight. Check all hardware again after first 50 hours of
operation and beginning of each planting season.
All hardware used on the Kinze planter is Grade 5 (high strength) unless otherwise noted. Grade 5 cap screws are
marked with three radial lines on the head. Hardware must be replaced with equal size, strength, and thread type.
WARNING
Loose transport wheel lug nuts can result in wheel separation from
planter and can result in death, serious injury, and damage to property
and equipment. Check transport wheel lug nut torque before operating
planter for the first time and periodically thereafter.
NOTICE
Over-tightening hardware can reduce its shock load capacity and cause
equipment failure.
TORqUE VALUES CHART - PLATED HARDWARE
Grade 2 Grade 5 Grade 8
Diameter Coarse Fine Coarse Fine Coarse Fine
¼ " 50 in-lb 56 in-lb 76 in-lb 87 in-lb 9 ft-lb 10 ft-lb
5∕16 " 8 ft-lb 9 ft-lb 13 ft-lb 14 ft-lb 18 ft-lb 20 ft-lb
⅜ " 15 ft-lb 17 ft-lb 23 ft-lb 26 ft-lb 33 ft-lb 37 ft-lb
7∕16 " 25 ft-lb 27 ft-lb 37 ft-lb 41 ft-lb 52 ft-lb 58 ft-lb
½ " 35 ft-lb 40 ft-lb 57 ft-lb 64 ft-lb 80 ft-lb 90 ft-lb
9∕16 " 50 ft-lb 60 ft-lb 80 ft-lb 90 ft-lb 115 ft-lb 130 ft-lb
⅝ " 70 ft-lb 80 ft-lb 110 ft-lb 125 ft-lb 160 ft-lb 180 ft-lb
¾ " 130 ft-lb 145 ft-lb 200 ft-lb 220 ft-lb 280 ft-lb 315 ft-lb
⅞ " 125 ft-lb 140 ft-lb 320 ft-lb 350 ft-lb 450 ft-lb 500 ft-lb
1" 190 ft-lb 205 ft-lb 480 ft-lb 530 ft-lb 675 ft-lb 750 ft-lb
1⅛" 265 ft-lb 300 ft-lb 600 ft-lb 670 ft-lb 960 ft-lb 1075 ft-lb
1¼" 375 ft-lb 415 ft-lb 840 ft-lb 930 ft-lb 1360 ft-lb 1500 ft-lb
1⅜" 490 ft-lb 560 ft-lb 1100 ft-lb 1250 ft-lb 1780 ft-lb 2030 ft-lb
1½" 650 ft-lb 730 ft-lb 1450 ft-lb 1650 ft-lb 2307 ft-lb 2670 ft-lb
NOTE: Torque unplated hardware and bolts with lock nuts approximately ⅓ higher than above values. Torque bolts lubricated
prior to installation to 70% of value shown in chart.
SPECIAL TORqUE VALUES & INSTRUCTIONS
Row unit parallel linkage bushing hardware 130 ft-lb (176 Nm)
5/8 " No till coulter spindle hardware 120 ft-lb (162 Nm)
Transport Tire Inner Budd Nuts 315 ft-lb (427 Nm)
Transport Tire Outer Budd Nuts 1075 ft-lb (1458 Nm)
Row Unit Disc Opener Blade Bolt** 110 ft-lb (149 Nm)
**Left hand side is left
hand thread.
5/8 " - 18 Wheel Lug Nuts and Lug Bolts 200 ft-lb (271 Nm)
9/16 " - 18 Wheel Lug Nuts and Lug Bolts 125 ft-lb (169 Nm)