SARGENT Profile Series Cylindrical Locks - Manual (Page 5)

C
o
p
yr
ig
h
t
©
S A
R
G
EN
T
M
a
n
u
fa
c
tu
ri
n
g
.A
ll
ri
g
h
ts
re
se
rv
e
d
.
R
e
p
ro
d
u
c
ti
o
n
in
w
h
o
le
o
r
in
p
a rt
w
it
h
o
u
t
th
e
e
xp
re
ss
w
ri
tt
e
n
p
e
rm
is
si
o
n
o
f
S
A
R
G
EN
T
M
a
n
u
fa
c tu
ri
n
g
is
p
ro
h
ib
it
e
d
.
3
A7857A • 800-810-WIRE (9473) • www.sargentlock.com
Door Name 5666
Seq User Trans
0 001 —
1 003 —
2 003 —
3 020 —
4 003 —
Transaction
number Transaction
type
User
number
Door
name
Varies
Keypad Programming Instructions for the Profile Series LK Lock
Hold an infrared printer up to the infrared LED (as
shown). An HP82240B Infrared Printer can be used to
download information from the keypad to a printout. For additional information, see “Transaction Log”.
To LED
location
Infrared
printer
(52-2069)
Note: Seq. # 0 is the
programming request
to output the entries.
Sequence numbers
1-9 are the actual
entries.
Enter A One Time User Code
99# Master Code* or Supervisory Code* Yellow LED blinks
50# 5# (User Number 04-100)# Yellow LED blinks
User Code (1-6 digits)* Yellow LED blinks quickly
User Code (1-6 digits)* Yellow LED blinks slowly
(If solid, see note)
* Yellow LED goes out
To Deactivate/Reactivate “Beep” With Key Stroke
99# Supervisory or Master Code* Yellow LED blinks
30# 0# 0# (Off) (1# = On) Yellow LED blinks
* Yellow LED blinks quickly
* Yellow LED blinks slowly (If solid, see note)
* Yellow LED goes out
Note: If turning beep off, not audible on last two steps.
Reset Master Code back to factory default (1234) and retains all other User codes
99# Master Code* Yellow LED blinks
40# 00000# 00000# Yellow LED blinks
* Yellow LED blinks quickly
* Yellow LED blinks very fast for 10 sec., then slow
* Yellow LED goes out
If the Master Code is not known, factory assistance will be required. Call 1-800-810-9473.
To Clear the Entire Memory
99# Master Code* Yellow LED blinks
46# 00000# 00000# Yellow LED blinks
* Yellow LED blinks quickly
* Yellow LED goes solid and begins to blink
* Yellow LED goes out (If solid, see note)
This deletes ALL Codes, including Master, Emergency and Supervisory. The Master Code is set back to 1234*,
Sets Unlock Time to 5 seconds. If the Master Code is not known, factory assistance will be required to clear the
memory. Call 1-800-810-9473.
To Program Door Name into Keypad
99# Master Code* Yellow LED blinks
43# Door Name (up to 5 digits)# Yellow LED blinks
0# Yellow LED blinks quickly
* Yellow LED blinks slowly (If solid, see note)
* Yellow LED goes out
To Interrogate Transaction Log
99# Supervisory or Master Code* Yellow LED blinks
70# 0# 0# Yellow LED blinks
* Yellow LED blinks quickly
* Yellow LED goes out (If solid, see note)
When done printing, the green LED will turn off and the yellow LED will blink slowly.
*
Yellow LED goes out