Document Outline

• Table of contents
• 1 Safety information and use
  • 1.1 Requirements for the user
  • 1.2 Scope of application
    • 1.2.1 Operating principle
    • 1.2.2 Drive motor and speed regulation
  • 1.3 Obligations of the operator
  • 1.4 Information on hazards and symbols used in this manual
  • 1.5 Information on hazards at the device
  • 1.6 Device safety information
  • 1.7 Protective equipment
  • 1.8 Hazardous points
  • 1.9 Electrical safety
    • 1.9.1 General information
    • 1.9.2 Protection against restart
    • 1.9.3 Overload protection
    • 1.9.4 Imbalance detection
• 2 Technical data
  • 2.1 Dimensions
  • 2.2 Weight
  • 2.3 Operating noise
  • 2.4 Voltage
  • 2.5 Current consumption
  • 2.6 Power consumption
  • 2.7 Electrical fuses
  • 2.8 Material
  • 2.9 Final fineness
• 3 Installation
  • 3.1 Transport
  • 3.2 Unpacking
  • 3.3 Setting up
  • 3.4 Ambient conditions
  • 3.5 Electrical connection
• 4 Initial start-up
  • 4.1 Switching on
  • 4.2 Function check
  • 4.3 Switching off
• 5 Using the device
  • 5.1 Safety information
    • 5.1.1 General information
    • 5.1.2 Overpressure relief of the grinding bowls
    • 5.1.3 Grinding bowl lid
  • 5.2 Choice of grinding bowls and grinding balls
    • 5.2.1 Useful capacity of the grinding bowls
    • 5.2.2 Size of the grinding balls
    • 5.2.3 Number of balls per grinding bowl (independent of the material quantity)
    • 5.2.4 Calculated weight of a ball
  • 5.3 Impact of the ball size and the material during grinding
  • 5.4 Filling quantities of grinding bowls
  • 5.5 Filling the grinding bowl
  • 5.6 Factors with an impact on grinding
    • 5.6.1 Running time (grinding duration)
    • 5.6.2 Speed
    • 5.6.3 Reverse mode
    • 5.6.4 Number and size of the balls
    • 5.6.5 Weight of the balls (type of material)
  • 5.7 Dry grinding
  • 5.8 Wet grinding (grinding in a suspension)
    • 5.8.1 The effect of high temperature
    • 5.8.2 Safety measures against an excessively high pressure
  • 5.9 Handling the grinding bowl
    • 5.9.1 Design
    • 5.9.2 Opening the grinding bowl after a grinding operation
    • 5.9.3 Closing the grinding bowl
    • 5.9.4 Inserting the grinding bowl in the grinding bowl holder
    • 5.9.5 Removing the grinding bowl
  • 5.10 Mass balance
  • 5.11 Grinding duration
  • 5.12 Conducting a grinding operation
    • 5.12.1 Program sequence after switching on
    • 5.12.2 Starting grinding at high speed
    • 5.12.3 Overload
    • 5.12.4 "Program" menu item
    • 5.12.5 Saving the current data
    • 5.12.6 Loading the program
    • 5.12.7 Setting the time control
    • 5.12.8 Imbalance check
    • 5.12.9 Switching off
    • 5.12.10 Cooling the grinding bowl
• 6 Accessories
  • 6.1 Standard gassing lid for grinding with inert gas
    • 6.1.1 Scope of delivery
    • 6.1.2 Fitting the gassing lid on the grinding bowl
    • 6.1.3 Hose adapter for grinding bowl gassing
    • 6.1.4 Removing the gassing lid in individual steps
  • 6.2 Gassing lid with stainless steel, swagelok hose couplings
    • 6.2.1 Scope of delivery / lid design
    • 6.2.2 Fitting the gassing lid on the grinding bowl
    • 6.2.3 Hose adapter for grinding bowl gassing
    • 6.2.4 Removing the gassing lid in individual steps
  • 6.3 EASY GTM Gas Pressure and Temperature Measuring System
    • 6.3.1 Case contents and system design
    • 6.3.2 Inserting / changing the battery
    • 6.3.3 Configuration of transmitter ID and data transmission frequency
      • 6.3.3.1 Adjustment options of the transmitter detection
      • 6.3.3.2 Transmission frequency setting options
    • 6.3.4 Installation of the transmission unit on the EASY GTM bowl
    • 6.3.5 Installation of the receiver board in the P-7 premium line
    • 6.3.6 Activating EASY GTM
    • 6.3.7 Entering the temperature limit
    • 6.3.8 Entering the pressure limit
    • 6.3.9 Selecting the operating mode
    • 6.3.10 Deactivating EASY GTM
    • 6.3.11 Cleaning the EASY GTM system
      • 6.3.11.1 Cleaning the sensor and replacing the seal
    • 6.3.12 Battery arrangement
  • 6.4 Special emptying device for grinding bowls
    • 6.4.1 Design
    • 6.4.2 Handling
    • 6.4.3 Cleaning the special emptying device
  • 6.5 Compl. counterweight
    • 6.5.1 Design
    • 6.5.2 Handling
  • 6.6 Planetary mills - "MillControl" software
• 7 General and optional settings
  • 7.1 Standard Operation Procedure
    • 7.1.1 Activating SOP mode
    • 7.1.2 Deactivating SOP mode
    • 7.1.3 Deleting SOP mode
  • 7.2 RFID
  • 7.3 Language change
  • 7.4 Screen brightness
  • 7.5 Information
  • 7.6 Interfaces
  • 7.7 Firmware update
• 8 Cleaning
  • 8.1 Grinding elements
  • 8.2 Mill
    • 8.2.1 Removing the grinding chamber cover
• 9 Maintenance
• 10 Guarantee terms
• 11 Exclusion of liability
• 12 Safety logbook
• 13 Index