Document Outline

• Safety Precautions
  • Symbols
  • General Pecautions
  • Unpacking
  • WARRANTIES AND DISCLAIMERS
• Contents
• Chapter 1 Laser Safety Precuations
  • 1-1 Classification
  • 1-2 Warning Labels
  • 1-3 Label Location
  • 1-4 Safety Consideration
  • 1-5 Safety Features Provided with the LS-3100(W) Series
  • 1-6 Preparation for Operation
  • 1-7 Connecting 2 Scanning Heads
• Chapter 2 Trial Operation
• Chapter 3 Quick Setup Procedures
  • 3-1 Common Settings
    • Setting the Numberof Measurements for Averaging
    • Tolerance Settings
  • 3-2 Measurement Procedures
    • Outer Diameter Measurements
    • Gap Measurement 1 (When part of the target is outside the optical axis)
    • Gap Measurement 2 (When all of the target is within the optical axis)
    • Measuring Roundness (When target is rotating)
    • Measuring Eccentricity (When target is rotating)
    • Measuring Target Displacement within the Measuring Range
    • Measuring Edge Movement
  • 3.3 Using LS-3100D(W) Controller with 2 Scanning Heads
• Chapter 4 Functions and Controls
  • 4-1 Part Names
    • Controller
    • Scanning Heads
  • 4-2 Indicators and Displays
  • 4-3 Panel Keys
    • Numeric Keys
    • SET Key
    • CLR Key
    • ENT Key
    • UP/DOWN Key
    • ZERO (Auto-Zero) Key
    • HOLD Key
    • AVE Key
    • PRM Selector Key
    • LIMIT (Tolerance limits for 3-step differentiation) Key
    • SEG (Segment) Key
    • FNC (Function) Key
    • MODE Key
    • CAL (Calibration) Key
    • DISP (Subdisplay) Key
    • OFS (Offset) Key
    • PROG (Program) Key
  • 4-4 I/O Terminal
    • RS-232C I/O Terminal
    • 36-pin Connector (Control I/O)
    • Functions of Terminal Blocks
• Chapter 5 Mounting Scanning Head
  • 5-1 Alignment of Optical Axis (LS-3060 and LS-3033 only)
    • Allowance forAligning Transmitterand Receiver
  • 5-2 Checking Alignment of Optical Axis (LS-3033 and LS-3060 only)
    • Error Messages (For Models LS-3060 and LS-3033)
• Chapter 6 Optional Interface Boards
  • 6-1 BCD Output
    • Specifications
    • Pin Assignment
    • Output Signal
    • Input Signal
  • 6-2 GP-IB Interface I/O
    • Specifications
    • Pin Assignment
    • Interface Functions
    • Initial Setting
    • Interface Messages
    • Listener-talker Functions
    • Basic Sequence
    • Example of Program
• Chapter 7 Hints on Correct Use
• Chapter 8 Error Messages
  • H-Err
  • P-Err
  • CALIB ERROR
• Chapter 9 Troubleshooting Guide
• Appendix A Operating Principle
• Appendix B Characteristics
  • Measuring Area vs. Accuracy
  • Temperature Characteristics (Typical)
• Appendix C Specifications
  • Controller
  • Scanning Head
• Appendix D Dimensions
• Appendix E Quick Refference Table
  • Modes (Function) and Key Operations
• Appendix F Key Flowcharts
  • PRM (Parameter)
  • AVE (Average)
  • 93SEG (Segment)
  • FNC (Function)
  • DISP (Display)
  • MODE
  • PROG (Program)
  • OFS (Offset)
  • LIMIT
  • CAL (Calibration)
• WARRANTIES AND DISCLAIMERS