Muratec F-150 - Manual (Page 83)

Beyond the basics
• Mode 1 (the display calls it “Mode1”) — Your fax machine checks whether any
phone number in your autodialer matches the last four digits of the remote fax’s
subscriber
ID (remember, that’s the phone number part of the TTI ). If it doesn’t
find such a match, your machine disconnects the call.
• Mode 2 (“Mode2”) — This mode rejects any call from a number whose last eight
digits match any number in the blocked numbers list (we’ll explain).
• Mode 3 (“Mode3”) — This rejects both numbers not in the autodialer and numbers
that are in the blocked numbers list. This lets you keep a number on your autodi-
aler yet still block its incoming calls by putting it in the blocked numbers list.
So, before you activate the Block Junk Fax feature, please consider:
• Not all fax machine owners enter their phone numbers in their Subscriber
ID s. —
With this feature activated, your machine would reject faxes from such machines.
• Access codes can cause confusion. — If an autodialer entry ends with long-dis-
tance or other codes, Block Junk Fax will block out calls from those faxes (i. e.,
those other fax users won’t put your codes at the end of their Subscriber
ID s).
If you do decide to go ahead with activating Block Junk Fax, here’s how:
1 Press / PROGRAM , J , 1, 2, ENTER . The LCD shows your fax’s current setting:
If the setting you see is acceptable, skip to step 3.
Otherwise, proceed to step 2.
2 To change the setting, press or / PROGRAM once or twice until your chosen
setting appears. In this example, we’ve chosen Mode2.
3 Press ENTER to save the setting.
What you do next depends upon what you selected in step 1 or 2:
• If either Off or Mode1, your machine will return to standby mode.
• If either Mode2 or Mode3, proceed to step 4.
4 The LCD now asks whether you want to enter a number:
If you wish to enter or modify a number, press ENTER and proceed to step 5.
Otherwise, press / PROGRAM and skip to step 10.
5 Depending on whether you already have entered at least one number into the
blocked numbers list, the display shows one of the following:
or
If you have not entered any numbers in the blocked numbers list, skip to step 7.
Otherwise, proceed to step 6.
6 If you wish to modify an existing entry in the blocked numbers list, press
/ PROGRAM repeatedly until you see the number you wish to modify.
… or …
If you wish to enter a new number in an already-started blocked numbers
list, press /
PROGRAM repeatedly until you find an empty position in the list
(as in the first display in step 5).
Note: To clear a number from the list, see “Clearing a number from the
blocked numbers list,” below.
7 Use the numeric keypad to enter the last eight characters of a fax number you
wish to block. For example, if you wish to block a fax from someone with a
Subscriber
ID of 972-555-3038, you should enter 5, 5, 5, -, 3, 0, 3, 8:
To change only a specific digit of an entry, press to move leftward or
/ PROGRAM to move rightward until the cursor is under the digit, then use
the numeric keypad to enter the correct digit.
8 Press ENTER to save the setting. The display will show the next “slot” in the
blocked numbers list.
If you do not wish to enter or change a number for this slot, proceed to step 9.
If you do wish to enter or change a number for this slot, repeat steps 5–8.
9 Press STOP . The display now asks whether you want to print the list.
10 If you do want to print the list, press ENTER and your machine will print it.
If you don’t want to print it, press STOP and your machine will return to its
normal standby mode.
Clearing a number from the blocked numbers list
To clear a number from the list:
1 Press / PROGRAM , J , 1, 2, ENTER .
If your Block Junk Fax setting is either Mode2 or Mode3, skip to step 3.
Enter Fax Number
01:555-3038
Enter Fax Number
01:_
Set BlockJunk Dial
Program/Enter
Block Junk
Fax:Mode2
Block Junk Fax:Off
Program/Enter
2.54