Panasonic AJ-HDX400P - Manual (Page 41)

4
Chapter 4 Adjustments and settings for recording
41
Display item What is displayed Status when display appears
7 Cumulative gain
display
6 :/10:/12:/15:/20: This indicates the value of the cumulative gain (DS.GAIN) when this
gain function is working.
9 Gain value ¢¢ dB This indicates the current gain value.
8 8 LINE MIX GAIN
display
M This appears when LINE MIX GAIN (+6 dB) is active.
6 WHITE BAL switch
position
A
B
P
T This indicates that the WHITE BAL switch is set to channel A.
This indicates that the WHITE BAL switch is set to channel B.
This indicates that the WHITE BAL switch is set to PRE.
This indicates that the ATW mode has been set. It flashes when the
brightness and color are outside the operating range.
5 Filter positions 1 to 4
A to D
– This indicates the position of the ND filter.
This indicates the position of the CC filter.
This indicates that the filter has not been set to a proper position.
4 Information
allocated to USER
buttons
UM: USER MAIN
U1: USER1 button
U2: USER2 button
INH
S.GAIN ¢¢dB/OFF
DS.GAIN ¢¢
:/OFF
LINE MIX ON/OFF
S.IRIS ON/OFF
I.OVR ON/OFF
S.BLK –¢¢/OFF
B.STR ON/OFF
AUDIO CH1
AUDIO CH2
REC SW
Y GET ON
RET SW
ATW ON/OFF
D.ZOOM a2/a3/a4/OFF
“INH” is indicated when the operation of the USER button has been disabled.
This indicates the value selected for S.GAIN.
This indicates the value selected for DS.GAIN.
This indicates whether LINE MIX GAIN is set to ON or OFF.
This indicates whether S.IRIS is set to ON or OFF.
This appears when the IRIS OVERRIDE setting is enabled (ON).
This indicates whether SUPER BLACK is set to ON or OFF and, if it is
set to ON, it also indicates its value.
This indicates whether BLACK STRETCH (black level gradation
compensation) is set to ON or OFF.
This appears when the input signal to recorded on audio channel 1 has
been switched.
This appears when the input signal to recorded on audio channel 2 has
been switched.
This appears only during MODE CHECK button operations while the
USER button functions as the REC switch.
This appears when the function for measuring the output brightness level (in
% units for approx. 3 seconds for the area near the center marker) is ON.
This appears only during MODE CHECK button operations while the
USER button functions as the RET switch.
This appears when ATW is operating.
This indicates the D.ZOOM status.
; AUDIO input
system and level
meter
This indicates the audio channels selected and their audio levels.
This appears when the AUDIO IN switch is at the FRONT position.
This appears when the AUDIO IN switch is at the WIRELESS position.
This appears when the AUDIO IN switch is at the REAR position.
---- ---+ ∫
: VTR warnings,
information
REC WARNING
SLACK E-¢¢
HUMID
SERVO
RF
BACKUP BATT EMPTY
WIRELESS-RF
This indicates that a problem has occurred during recording.
This indicates that a problem has occurred in a mechanism. Depending on the
nature of the trouble concerned, the power may be turned off automatically.
This indicates that condensation has formed.
This indicates that servo lock has not been initiated during recording or
playback.
This indicates that the level of the signals from the tape has dropped.
This signals that it is time to replace the backup battery.
This indicates that the level of the RF signal from the wireless
microphone receiver has dropped.
<Note>
For details on the codes displayed in this area, refer to “6-3-2 Error codes.”
< Time code display TCG 12:59:59:20
TCR 12:59:59:20
(V)UBG AB CD EF 00
(V)UBR 12 34 56 78
CTL –01:59:59:20
This indicates the TCG (time code generator) value.
This indicates the TCR (time code reader) value.
This indicates the UBG VUBG display.
This indicates the UBR VUBR display.
This indicates the CTL-COUNTER value.
F
W
R