Panasonic AJ-HDX400P - Manual (Page 82)

Chapter 7 Menu description tables
82
7-3-8 SKIN TONE DTL
Item/
Data storage
Variable
range
Remarks
$ SKIN TONE DTL ON
OFF For selecting ON or OFF for the skin tone
DTL.
$ SKIN TONE
ZEBRA
ON
OFF For selecting ON or OFF for ZEBRA in the
SKIN TONE range.
SKIN DTL CORING 0
:
5
:
7
For setting the SKIN TONE DTL coring effect.
<Note>
ZEBRA signals are superimposed only when
menu operations have been performed to
open the <SKIN TONE DTL> page and ON
has been selected as the SKIN TONE ZEBRA
item setting. Exercise care during operation
since these signals will be superimposed onto
not only the viewfinder but the main line
system as well.
Y MAX 000
:
190
:
255
For setting the maximum luminance signal
value for applying the SKIN TONE effect.
Y MIN 000
:
010
:
255
For setting the minimum luminance signal
value for applying the SKIN TONE effect.
I CENTER 000
:
035
:
255
For setting the center position on the I axis
(setting the area to which the SKIN TONE
effect is to be applied).
I WIDTH 000
:
055
:
255
For setting the width of the area to which the
SKIN TONE effect is to be applied on the I
axis centered on the I CENTER.
Q WIDTH 000
:
010
:
255
For setting the width of the area to which the
SKIN TONE effect is to be applied on the Q
axis centered on the I CENTER.
Q PHASE –31
:
+00
:
+31
For setting the phase of the area to which the
SKIN TONE effect is to be applied as
referenced to the Q axis.
R-Y
B-Y
Q-WIDTH
I-WIDTH
Q-PHASE
I-CENTER
Y
Y-MAX
Y-MIN
0
=SKIN TONE AREA
– direction
+ direction
The underlining in the variable range column indicates the setting in the preset mode.
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
7-3-9 KNEE/LEVEL
Item/
Data storage
Variable
range
Remarks
MASTER PED –200
:
+018
:
+200
For performing the MASTER PEDESTAL
setting.
$ MANUAL KNEE ON
OFF For setting the mode which is to be established
when the AUTO KNEE switch is at OFF. The
KNEE POINT/SLOPE setting value is active
when ON is selected.
KNEE POINT 70.0%
:
93.0%
:
107.0%
For setting the KNEE POINT position in 0.5%
steps.
KNEE SLOPE 00
:
85
:
99 (98)
For performing the KNEE width setting.
Same as KNEE OFF when set to 0.
<Note>
The range of values that can be selected
using the AJ-EC3P is 00 to 98.
WHITE CLIP LVL 90%
:
109%
For performing the WHITE CLIP LEVEL
setting.
A.KNEE POINT 80%
:
93%
:
107%
For setting the AUTO KNEE POINT position
in 0.5% steps. This item is active when the
OUTPUT/AUTO KNEE selector switch is set
to CAM.AUTO KNEE ON.
A.KNEE LVL 100
:
107
:
109
For performing the AUTO KNEE level setting.
A.KNEE
RESPONSE 1
:
4
For setting the AUTO KNEE response speed.
$ WHITE CLIP ON
OFF For selecting ON or OFF for the WHITE CLIP
function. The WHITE CLIP LVL setting value
is active when ON is selected.
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
S C U F E
<Note>
Items with $ in front of their names are set by the PAINT
MENU SW ($) R/W menu items on the <CARD R/W
SELECT> screen.
Items without $ in front of their names are set by the PAINT
MENU LEVEL R/W menu item.
For details, refer to “7-6-2 CARD R/W SELECT.”