Panasonic AJ-HDX400P - Manual (Page 84)

Chapter 7 Menu description tables
84
ECU MENU DISP. ON
OFF For selecting ON or OFF for displaying the
MENU on the viewfinder when the ECU is
connected.
7-4 VF
7-4-1 VF DISPLAYS
Item/
Data storage
Variable
range
Remarks
DISP CONDITION NORMAL
HOLD NORMAL: The statuses are displayed at all
times.
HOLD: The statuses are displayed only
when the MODE CHECK switch is
pressed.
DISP MODE 1
2
3 For performing the DISP MODE setting. This
item is used to select the camera’s warning or
message displays. For details, refer to “4-7-4
Display modes and setting changes/
adjustment result messages.”
VF OUT Y
NAM
R
G
B For selecting the VF output.
Y:
Luminance signal
NAM: The signal with the highest level among
the R, G and B signals is output.
R: R channel signal
G: G channel signal
B: B channel signal
VF DTL 0
:
3
:
5
For performing the VF DTL selection. This
item is used to further emphasize the DTL of
the VF signals. If 0 is set, the DTL will be the
same as that of the main line signals.
ZEBRA1 DETECT 0%
:
70%
:
109%
For setting the ZEBRA1 detection level (IRE
level).
ZEBRA2 DETECT 0%
:
85%
:
109%
For setting the ZEBRA2 detection level (IRE
level).
ZEBRA2 ON
SPOT
OFF For selecting ON or OFF for ZEBRA2 or
selecting SPOT.
LOW LIGHT LVL OFF
10%
15%
20%
25%
30%
35% For setting how much lower the camera’s
input light quantity should be in order for
“LOW LIGHT” to be displayed.
MARKER/
CHAR LVL 50%
60%
70%
80%
90%
100% For setting the brightness of the markers and
characters displayed in the viewfinder.
The underlining in the variable range column indicates the setting in the preset mode.
C U F E
C U F E
C U F E
C U F E
C U F E
C U F E
C U F E
C U F E
C U F E
C U F E
C U F E
DS.GAIN DISP GAIN
FRM RATE For selecting whether to display the DS.GAIN
value as a frame rate value (P) or gain value
(
).
GAIN: The DS.GAIN value is displayed
as a gain value (
).
FRM RATE: The DS.GAIN value is displayed
as a frame rate value (P).
7-4-2 VF MARKER
Item/
Data storage
Variable
range
Remarks
TABLE A
B For selecting the VF MARKER setting table.
This item is used to set the current values of
table A or B which have been selected using
the menu items listed below.
CENTER MARK OFF
1
2
3
4 For selecting the center marker.
OFF: The center marker is not displayed.
1:
+ (large)
2: Center blank (large)
3: + (small)
4: Center blank (small)
SAFETY ZONE OFF
1
2 For selecting the type of safety zone frame.
OFF: The safety zone frame is not displayed.
1:
Box
2: Corner frames
SAFETY AREA 80%
:
90%
:
100%
For setting the position of the safety zone.
FRAME SIG 4:3
13:9
14:9
VISTA For setting the frame marker.
The VISTA setting is 16:8.65.
FRAME MARK ON
OFF For selecting ON or OFF for the frame
marker.
FRAME LVL 00
:
15
For setting the level of the frame marker.
0:
Equivalent to signal OFF
15: Same brightness as center area
However, this setting has no effect if
FRAME SIG is set to VISTA.
C U F E
C U F E
C U F E
C U F E
C U F E
C U F E
C U F E
Zebra pattern display
Video level
SPOT OFF ON
109%
0%
ZEBRA 2
DETECT
ZEBRA 2
ZEBRA 1
DETECT