Teledyne LeCroy PETracer Summit and Summit T2-16 PCIe User Manual - Manual (Page 3)

Summit User Manual
Teledyne LeCroy
iii
T
ABLE OF
C
ONTENTS
Section 1. General. . . . . . . . . . . . . . . . . . . . . 1
Chapter 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 PETracer Analyzer Hardware and Software . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 CATC Trace Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Summit T2-16 Analyzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 PETracer Gen2 Summit Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5 Other Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 2 Hardware Description . . . . . . . . . . . . . . . . . . . 9
2.1 System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Host Machine Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Summit T2-16 Front Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LCD Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4 PETracer Summit Front Panel Description . . . . . . . . . . . . . . . . . . . . . . . . 13
LCD Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.5 Summit T2-16 Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.6 PETracer Summit Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . . . 18
2.7 External Interface Breakout Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Pin-Outs for the Data In/Out Connector . . . . . . . . . . . . . . . . . . . . . . . . 21
Prototype Rework Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Breakout Board Input and Output Signals. . . . . . . . . . . . . . . . . . . . . . . 22
Chapter 3 Installation and Setup . . . . . . . . . . . . . . . . . . 23
3.1 Installing the PETracer Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2 Setting Up the Summit T2-16 Analyzer using an Ethernet Connection. . . 25
Connecting to a Summit T2-16 Analyzer in the Local Network. . . . . . . 25
3.3 Setting Up the Summit T2-16 Analyzer using a USB Connection . . . . . . . 28
3.4 Setting Up the PETracer Summit Analyzer . . . . . . . . . . . . . . . . . . . . . . . . 29
Connecting to a PETracer Summit Analyzer in the Local Network . . . . 29
3.5 Interposers and Probes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.6 Using Probes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Example: Connecting the Summit T2-16 Analyzer to the Device Under
Test Using a Gen2 MidBus Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Example: Connecting the Summit T2-16 Analyzer to the Device Under
Test Using a Gen2 Multi-lead Probe for x1 and x4 . . . . . . . . . . . . . . . . 36
Example: Connecting the Summit T2-16 Analyzer to the Device Under
Test Using a Gen2 Multi-lead Probe for x8 and x16 . . . . . . . . . . . . . . . 38
3.7 Using Interposers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Example: Connecting the Summit T2-16 Analyzer to the Device Under
Test Using a Gen2 Passive Interposer . . . . . . . . . . . . . . . . . . . . . . . . . 40
Example: Connecting the Summit T2-16 Analyzer to the Device Under
Test Using a Gen2 Active Interposer. . . . . . . . . . . . . . . . . . . . . . . . . . . 42