Breville ESPRESSO MACHINE User Manual
Page 10
CAUTION: DO NOT ALLOW MILK TO RUN OVER THE TOP OF THE FROTHING ATTACHMENT, OTHERWISE IT
WILL NOT FUNCTION PROPERLY.
TO AVOID SPLATTERING OF HOT MILK, DO NOT LIFT THE END OF THE FROTHING ATTACHMENT
ABOVE THE SURFACE OF THE MILK WHILE FROTHING.
ENSURE THE SELECTOR CONTROL IS IN THE ‘STANDBY’ POSITION BEFORE REMOVING THE
1 9
•
Hold the frothing jug at an angle so that
the Frothing Attachment sits just below
the surface of the heating milk and the
steam will move the milk around the
inside of the jug in a circular motion.
•
When the milk starts to increase in
volume, immerse the Frothing
Attachment deeper into the jug to heat
the milk.
•
Hold the jug at an angle with one hand
and place your other hand on the outer
base of the stainless frothing jug.
•
When the base of the jug becomes too
hot to touch, set the Selector Control to
the ‘Standby’ position, stopping the
steaming function before removing the
jug. A pumping noise will sound for a
short time.
•
Pour the steamed milk into each cup of
freshly brewed espresso coffee and
spoon in the frothed milk, in the
following ratios: Cappuccino -
1
/
3
espresso,
1
/
3
steamed milk,
1
/
3
frothed milk
Latté -
1
/
3
espresso topped with
steamed milk and about 1cm of frothed
milk (traditionally served in a glass)
STEAM BUTTON/HOT WATER BUTTON
•
The Steam button surround will
automatically illuminate when the
machine is switched ‘On’ with the Power
On/Off button.
•
The machine will always automatically
default to the Steam button when the
appliance is first switched on.
•
Both buttons cannot be operated at the
same time.
•
To select steam: when the Steam button
surround is illuminated, just set the
Selector Control to ‘Steam’
•
To select hot water: press the Hot
Water button and the surround will
illuminate, then just set the Selector
Control to ‘Steam’.
•
If the machine remains switched ‘On’,
the last button function used (Steam or
Hot Water) will stay illuminated.
HOW TO FROTH MILK FOR A CAPPUCCINO OR LATTÉ
1
/
3
full with cold fresh milk.
•
Turn the Selector Control to the ‘Steam’
position and press the ‘Steam’ button.
(Refer to information on Steam and Hot
Water buttons on Page 19.) The
‘Heating’
light will start to flash indicating that the
Thermoblock Heating System is heating
and preparing to create steam.
•
When the red ‘Heating’ light stops
flashing, quickly insert the Steam Wand
into the jug of milk so that the Froth
Attachment is just immersed into the
milk.
1 8
HOW TO FROTH MILK FOR A CAPPUCCINO OR LATTÉ
NOTE: Always ensure that the
Frothing Attachment has
been firmly pushed onto the
Steam Wand and connects
with the rubber surround.
For best results use cold
fresh milk (low fat milk will
froth easier)
.
Always clean the Steam
Wand and Frothing
Attachment after every
NOTE: When the 800ESXL is
creating steam a pulsing
noise can be heard. This is
the normal operation of the
NOTE: If steam starts coming
from
the Steam Wand before it is
immersed in the milk, pause
the steam by turning the
Selector Control back to the
‘Standby’ position. This
will avoid the steam
pressure blowing milk out
NOTE: The 800ESXL features a
Swivel Steam Wand
assembly so
the position of the Steam
Wand can be changed to a
BR6659_800ESXL_Book_US.qxp 15/2/06 4:54 PM Page 18