Rockwell Automation 1746-BTM Barrel Temperature Control Module User Manual - Manual (Page 39)

Publication 1746-UM010B-EN-P - April 2001
Configuring the Module 3-13
Table 3.B Block Header (word 0 / N10:0) = 8801 (-30719 decimal)
Loops 1-4
Word #
Set a bit or enter a value
1 2 3 4 bit to Configure Bit Select or Range 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1 26 51 76
0-1 operation mode
Monitor, No PID Control 0 0
Control loop with PID 0 1
Disable loop 1 0
2-5 input type
Type J 0 0 0 0
Type K 0 0 0 1
6 alarm enable Disable = 0; Enable = 1 X
7-8 TC break configuration
disable PID loop (CV=0) 0 0
Use thermal runaway
CV 0 1
Use manual mode CV 1 0
9 reserved
10-11 Autotune gains
low gains 0 0
medium gains 0 1
high gains 1 0
very high gains 1 1
12 Barrel control Barrel=0;Non-barrel=1 X
13 Zone Inner=0; Outer=1 X
14-15 reserved
2 27 52 77 0-15 High CV limit % -100.00 thru +100.00% default = +100.00%
3 28 53 78 0-15 Low CV limit % -100.00 thru +100.00% default = 0.00%
4 29 54 79 0-15 CV for TC break -100.00 thru +100.00% default = 0.0
5 30 55 80 0-15 Standby setpoint 0.0 thru 3276.7° default = 0.0
6 31 56 81 0-15 Heat on time (min.) 0.00 thru 100.00 sec. default = 0.00
7 32 57 82 0-15 Heat TPO period 0.00 thru 100.00 sec. default = 5.00
8 33 58 83 0-15 Cool on time (min.) 0.00 thru 100.00 sec. default = 0.00
9 34 59 84 0-15 Cool TPO period 0.00 thru 100.00 sec. default = 5.00
10 35 60 85 0-15 PV alarm rate -3276.8 thru 3276.7°/s default = 0.0
11 36 61 86 0-15 Low temp alarm -3276.8 thru 3276.7°/s default = +999.9
12 37 62 87 0-15 High temp alarm -3276.8 thru 3276.7°/s default = +999.9
13 38 63 88 0-15 Low deviation -3276.8 thru 3276.7°/s default = +999.9
14 39 64 89 0-15 High deviation -3276.8 thru 3276.7°/s default = +999.9
15 40 65 90 0-15 Alarm dead band 0.0 thru 10.0° default = 0.0
16 41 66 91 0-15 Thermal Integrity Loss 0 thru 100° default = 5
17 42 67 92 0-15 Integrity Rate 0 thru 100 minutes default = 20
18 43 68 93 0-15 ramping 0 thru 100°/min. default = 0
19 44 69 94 reserved
20 45 70 95 0-15 Non-barrel autotune
disturb size 0.00-100.00% default = 10.00
21 46 71 96 0-15 Startup
aggressiveness factor 0 thru 100 default = 0 for heat or cool, only; 25 for heat/cool
<=25 <=50 <=75 <=99 reserved