Hardy HI 1746-WS - Manual (Page 5)

Table of Contents
iii
HI 1746-WS Weigh Scale Module - - - - - - - - - - - - - - - - 4-2
Local Mode of Operation - - - - - - - - - - - - - - - - - - - - 4-3
Remote Mode of Operation - - - - - - - - - - - - - - - - - - - 4-3
About M Files - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3
Direct M File Mapping - - - - - - - - - - - - - - - - - - - - - - - 4-3
Local Mode of Operation - - - - - - - - - - - - - - - - - - - - 4-3
Remote Mode of Operation - - - - - - - - - - - - - - - - - - - 4-5
M File Interface to Set Up for Local Mode of Operation - - - - - - - 4-5
M File Data Structure (Words 0 to 5) - - - - - - - - - - - - - - 4-5
Logical File Interface to Set Up for Remote Mode of
Operation (8 Word) - - - - - - - - - - - - - - - - - - - - - - - 4-6
About Logical Files - - - - - - - - - - - - - - - - - - - - - - - 4-6
Command Word Encoding - - - - - - - - - - - - - - - - - - - 4-7
Bits 15 & 14 - - - - - - - - - - - - - - - - - - - - - - - - 4-7
Bits 8-13 - - - - - - - - - - - - - - - - - - - - - - - - - - 4-7
Bits 0-7 - - - - - - - - - - - - - - - - - - - - - - - - - - 4-7
Writing to the 32 Word Logical O and logical M0 files - - - - - - 4-8
Command Word - - - - - - - - - - - - - - - - - - - - - - - - 4-8
Writing to the M0 file - - - - - - - - - - - - - - - - - - - - 4-8
For Example - - - - - - - - - - - - - - - - - - - - - - - - 4-8
Writing to the O file - - - - - - - - - - - - - - - - - - - - - 4-8
For Example - - - - - - - - - - - - - - - - - - - - - - - - 4-8
Words 1-7 - - - - - - - - - - - - - - - - - - - - - - - - - 4-8
Reading from the 32 Word Logical I and logical M1 files - - - - - 4-9
Command Word - - - - - - - - - - - - - - - - - - - - - - - - 4-9
Bits 15-14 set to “10” - - - - - - - - - - - - - - - - - - - - 4-9
For Example - - - - - - - - - - - - - - - - - - - - - - - - 4-9
Bits 15-14 set to “11” - - - - - - - - - - - - - - - - - - - - 4-9
For Example - - - - - - - - - - - - - - - - - - - - - - - - 4-9
Bits 15-14 set to “01” - - - - - - - - - - - - - - - - - - - - 4-9
Bits 15-14 set to “00” - - - - - - - - - - - - - - - - - - - - 4-9
Executable Command List - - - - - - - - - - - - - - - - - - - - - 4-10
Zero Command (ZEROCMD) - - - - - - - - - - - - - - - - - - 4-10
Tare Command (TARECMD) - - - - - - - - - - - - - - - - - - 4-10
Write Non-Volatile Command (WRITENONVOLATILE) - - - - - 4-11
Reload Non-Volatile (RELOADNONVOLATILE) - - - - - - - - - 4-11
Float Integer to Integer Conversion Command (FLOAT2INT) - - 4-12
Integer to Float Integer Conversion Command (INT2FLOAT) - - 4-12
Cal Low Command (CALLOWCMD) - - - - - - - - - - - - - - 4-13
Cal High Command (CALHIGHCMD) - - - - - - - - - - - - - - 4-13
C2 Cal Command (C2CALCMD) - - - - - - - - - - - - - - - - 4-13
Read C2 Serial Number Command (READC2SERIALNUM) - - 4-14
Set Parameters Command (SETPARAM) - - - - - - - - - - - - 4-14