Futaba 8FG 2.4GHz - Manual (Page 117)

117 )XQFWLRQVRI0RGHO0HQX +HOLFRSWHU)XQFWLRQV !
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button.
<SensorTouch™>
3,7WR58'PL[LQJ 5HYROXWLRQPL[LQJ
8VH WKLV PL[ ZKHQ \RX ZDQW WR VXSSUHVV WKH
UHDFWLRQWRUTXHJHQHUDWHGE\PDLQURWRUSLWFKDQG
VSHHG FKDQJHV GXULQJ SLWFK RSHUDWLRQ$GMXVW VR
that the nose does not move in the rudder direction.
1RUPDOFRQGLWLRQPL[LQJFXUYH!
The mixing curve rate should be started
using smaller values.
For a rotor with a clockwise operation
direction, when pitch was input at the plus
side, set these parameters so that mixing
is in the clockwise direction. First, trim at
hovering and then adjust the neutral
position.
1. Adjustment between slow and hovering
Repeatedly hover from take off and land
at a constant rate matched to your own
rhythm. Then adjust the pitch so that the
nose of the helicopter remains steady
when the throttle is raised and lowered.
2. Throttle high side (climbing and diving from
hovering)
Repeat climbing and diving from hovering
at a constant rate matched to your own
rhythm and adjust the pitch so that the nose
does not deflect when the throttle is raised
and lowered.
Note: When a GY Series or other heading hold
gyro is used, since correction is performed by
the gyro, this mix is not utilized. If this function
is used when the gyro operation mode is the
AVCS mode, the neutral position will change.
,GOHXSFRQGLWLRQPL[LQJFXUYH!
Set the mixing rate so that the rudder direction
DW KLJKVSHHG ÁLJKW LV VWUDLJKW DKHDG $GMXVW IRU
each condition used.
ŏ 6HOHFW >3,7 WR 58'@ DW WKH 0RGHO
menu and access the setup screen
shown below by touching the RTN
button.
&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH
ŏ7R QH[W SDJH
6HWWLQJPHWKRG
Ɣ$FWLYDWHWKHPL[LQJ
When using this function, move the cursor to
the [ACT] item and touch the RTN button to
switch to the data input mode.
Select the ACT mode by scrolling the touch
sensor.
*The display blinks.
Touch the RTN button to activate the mixing
and return to the cursor mode. (ON is
displayed.)
ƔSRLQWFXUYHVHWWLQJ
Move the cursor to the curve rate setting
item you want to adjust and touch the RTN
button to switch to the data input mode.
Adjust the rate by scrolling the touch sensor.
,QLWLDO YDOXH 3a3 
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
Repeat this procedure for each point.
Ɣ3LWFKFXUYHFRS\IXQFWLRQ
Move the cursor to COPY item and touch the
RTN button to switch to the data input mode.
Select the copy destination condition by
scrolling the touch sensor and touch the RTN
button. Select the [YES] and touch the RTN
button.