Futaba 8FG 2.4GHz - Manual (Page 90)

90 0RGHO0HQX $LUSODQH*OLGHU)XQFWLRQV !
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button.
<SensorTouch™>
ELE to CAMBER [Corresponding model type]: Airplane/glider, 2 ailerons or more
7KLVIXQFWLRQLVXVHGZKHQ\RXZDQWWRPL[WKH
FDPEHUÀDSVZLWKHOHYDWRURSHUDWLRQ:KHQXVHG
WKHIODSVDUHORZHUHGE\XSHOHYDWRUDQGOLIWLV
increased.
ŏ ,QÁLJKW PL[LQJ FDQ EH WXUQHG 212)) E\ DVVLJQLQJ
this to a switch. (Always ON at [--] setting)
ŏ 7KH PL[LQJ UDWH FDQ EH DGMXVWHG
ŏ 7KH UDQJH WKDW PL[LQJ GRHV QRW ZRUN QHDU WKH
neutral position of the elevator stick can be
adjusted. (Glider only)
1RWH 7KHHOHYDWRURQWKHWDLOOHVVZLQJZLOODOVR
EHHIIHFWHGZKHQWKLVPL[LVDFWLYDWHG
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the up or down mixing
rate item for each servo and touch the RTN
button to switch to the data input mode.
Adjust the rate independently by scrolling
the touch sensor.
,QLWLDO YDOXH 
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
6HWWLQJPHWKRG
Ɣ$FWLYDWHWKHIXQFWLRQ
Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode. Select the ACT mode by scrolling the
touch sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
function and return to the cursor mode. (ON
is displayed.)
When setting a switch, move the cursor to
the [SW] item and touch the RTN button to
call the selection screen. Select the switch
and set its ON direction. (Always ON at "--"
setting)
)RUDGHVFULSWLRQRIWKHVZLWFKVHOHFWLRQPHWKRGVHHWKH
description at the back of this manual.
Ɣ5DQJHVHWWLQJ *OLGHURQO\
Move the cursor to the [RANGE] item and
hold the elevator stick to the desired position
(upper or lower side) and then touch the RTN
button for one second to set the range.
7KHPL[LQJGRHVQRWZRUNQHDUQHXWUDORIWKHHOHYDWRUVWLFN
 ,QLWLDO YDOXH 
 $GMXVWPHQW UDQJH a
*OLGHU &XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
ŏ 6HOHFW >(/( WR &$0%(5@ DW WKH 0RGHO
menu and access the setup screen
shown below by touching the RTN
*The display screen is an example.
The actual screen depends on the
model type.
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH
ŏ7R QH[W SDJH