Futaba 8FG 2.4GHz - Manual (Page 70)

70 0RGHO0HQX &RPPRQ)XQFWLRQV !
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button.
<SensorTouch™>
CONDITION Flight condition's switch assignment, copy, priority change and
condition delay can be set. [except airplane type]
7KLVIXQFWLRQLQWKH0RGHOPHQXFDQEHXVHG
WRVZLWFKWKHVHWWLQJVRIXSWRÀLJKWFRQGLWLRQV
Please note this is not applicable to airplane type
selections.
Note: To prevent accidental activation of any
XQXVHGÁLJKWFRQGLWLRQVGXULQJÁLJKWVHWWKH
switch setting of those unused conditions to
null [--].
ŏ $ &RQGLWLRQ 'HOD\ IXQFWLRQ FDQ EH VHW
Unnecessary fuselage motion which may be
generated when there are sudden changes
in the servo positions and when there are
variations in the operating time between
channels during condition switching. The
delay can be set for each channel to ensure
maximum performance from your aircraft.
:KHQ VHWWLQJ WKH GHOD\ IXQFWLRQ IRU D VSHFLÀF
ÁLJKW FRQGLWLRQ WKH UHODWHG IXQFWLRQ FKDQJHV
after a delay corresponding to the set
amount.
ŏ , I P X O W L S O H F R Q G L W L R Q V Z H U H V H W  W K H L U
operational priority may be customized as
desired.
&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
ŏ 6HOHFW >&21',7,21@ DW WKH 0RGHO PHQX DQG
access the setup screen shown below by touching
the RTN button.
Select the copy destination condition by
scrolling the touch sensor. Then, touch the
RTN button.
*The current condition can not be selected for the copy
destination condition.
3. Move the cursor to the [COPY] item and
t o u c h t h e R T N b u t t o n . A c o n f i r m a t i o n
message appears.
*The display blinks.
3. Touch the RTN button for one second and
the copying is completed. (Touch the S1
button to stop copying.)
3ULRULW\FKDQJH
1. Move the cursor to the priority up-arrow or
down-arrow you want to change and touch
the RTN button.
The priority of the corresponding condition is
changed. (The last condition becomes the
highest priority.)
*The normal condition cannot be shifted. The priority is the
ORZHVW
&RQGLWLRQVZLWFKVHOHFWLRQGHOHWLRQ
1. Move the cursor to the switch item of the
condition you want to select/delete and
access the switch setup screen by touching
the RTN button and select the switch and ON
direction.
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
&RQGLWLRQFRS\
6HWXSVFUHHQSDJH
1. Move the cursor to the [SOURCE] item and
touch the RTN button to switch to the data
input mode.
Select the copy source condition by scrolling
the touch sensor. Then, touch the RTN button.
2. Move the cursor to the [DESTIN.] item and
touch the RTN button.
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH
ŏ7R QH[W SDJH
 &RQGLWLRQQDPH &RQGLWLRQVZLWFK