Futaba 8FG 2.4GHz - Manual (Page 85)

85 0RGHO0HQX $LUSODQH*OLGHU)XQFWLRQV !
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button.
<SensorTouch™>
AIL 3
(Chip Aileron)
AIL 4
(Chip Aileron)
AIL1
(Main Aileron)
AIL 2
(Main Aileron)
FLP 3
(Brake Flap)
FLP 4
(Brake Flap)
$,/WR%5$.()/3 >&RUUHVSRQGLQJ PRGHO W\SH@ *OLGHU  ÁDSV
7KLV PL[ RSHUDWHV WKH EUDNH IODSV )/3
in the aileron mode. When the aileron stick is
PDQLSXODWHGWKHDLOHURQDQGEUDNHÀDSVSHUIRUP
the aileron operation simultaneously and the roll
axis is improved.
ŏ 7KH DLOHURQ OHIW DQG ULJKW PL[LQJ UDWHV FDQ EH
DGMXVWHG VHSDUDWHO\ IRU HDFK ÁDS VHUYR
ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\
setting a switch. (Always ON at [--] setting)
ŏ /LQNLQJ FDQ EH VHW /LQN WKLV PL[ WR RWKHU PL[HV
ŏ 6HOHFW >$,/ WR %5.)/3@ DW WKH 0RGHO
menu and access the setup screen
shown below by touching the RTN
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH
ŏ7R QH[W SDJH
ŏ $GMXVWPHQW RI HDFK
ÁDS VHUYR
*The display screen is an example. The actual
screen depends on the model type.
&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
6HWWLQJPHWKRG
Ɣ$FWLYDWHWKHIXQFWLRQ
Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode. Select the ACT mode by scrolling the
touch sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
function and return to the cursor mode. (ON
is displayed.)
When setting a switch, move the cursor to
the [SW] item and touch the RTN button
to access the selection screen. Select the
switch and set its ON direction. (Always ON
at "--" setting)
)RUDGHVFULSWLRQRIWKHVZLWFKVHOHFWLRQPHWKRGVHHWKH
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the flap (FLP) 3~4 left or
right item and touch the RTN button to switch
to the data input mode. Adjust the mixing
rate independently by scrolling the touch
sensor.
,QLWLDO YDOXH 
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
Ɣ/LQNPRGHVHWWLQJ
To activate the mixing, move the cursor to
the [LINK] item and touch the RTN button to
switch to the data input mode. Select the
ON mode by scrolling the touch sensor.
*The display blinks.
Touch the RTN button to set the link mode
and return to the cursor mode.