Futaba 8FG 2.4GHz - Manual (Page 87)

87 0RGHO0HQX $LUSODQH*OLGHU)XQFWLRQV !
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button.
<SensorTouch™>
RUDDER 2
RUDDER RUDDER
V-TAIL
RUDDER 2
Winglet
RUDDER 1
Winglet
at Flying wing at Flying wing
( ) ( )
AIL 3 AIL 3
(Chip Aileron) (Chip Aileron)
AIL1
(Main Aileron)
AIL 2
(Main Aileron)
RUD to AIL [Corresponding model type]: Airplane/glider, general
7KLV IXQFWLRQ LV XVHG ZKHQ \RX ZDQW WR PL[
WKH DLOHURQV ZLWK UXGGHU LQSXW ,W LV XVHG ZKHQ
rudder is applied during roll maneuvers such
DV NQLIH HGJH IOLJKW ,W FDQ EH XVHG WR WXUQ RU
EDQNVFDOHPRGHOVODUJHPRGHOVHWFOLNHDIXOO
size aircraft.
ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\
setting a switch. (Always ON at [--] setting)
ŏ /LQNLQJ FDQ EH VHW /LQN WKLV PL[ WR RWKHU PL[HV
ŏ 7KH PL[LQJ UDWH FDQ DOVR EH DGMXVWHG
ŏ 6HOHFW >58' WR $,/@ DW WKH 0RGHO
menu and access the setup screen
shown below by touching the RTN
button.
*The display screen is an example.
The actual screen depends on the
model type.
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH
ŏ7R QH[W SDJH
6HWWLQJPHWKRG
Ɣ$FWLYDWHWKHIXQFWLRQ
Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode. Select the ACT mode by scrolling the
touch sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
function and return to the cursor mode. (ON
is displayed.)
When setting a switch, move the cursor to
the [SW] item and touch the RTN button to
call the selection screen. Select the switch
and set its ON direction. (Always ON at "--"
setting)
)RUDGHVFULSWLRQRIWKHVZLWFKVHOHFWLRQPHWKRGVHHWKH
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the left or right item
and touch the RTN button to switch to the
data input mode. Adjust the mixing rate
independently by scrolling the touch sensor.
,QLWLDO YDOXH 
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
Ɣ/LQNPRGHVHWWLQJ
To activate the link mixing, move the cursor
to the [LINK] item and touch the RTN button
to switch to the data input mode. Select the
ON mode by scrolling the touch sensor.
*The display blinks.
Touch the RTN button to set the link mode
and return to the cursor mode.
*OLGHU &XUUHQWO\VHOHFWHGFRQGLWLRQQDPH