Thr cut – Futaba 8FG 2.4GHz User Manual
Page 62
62
)XQFWLRQVRI/LQNDJH0HQX!
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Linkage
menu by touching the
RTN button.
<SensorTouch™>
THR CUT
Stops the engine safely and easily.(airplane and helicopter only)
7KURWWOH FXW SURYLGHV DQ HDV\ ZD\ WR VWRS WKH
HQJLQH *HQHUDOO\ VSHDNLQJ PRGHOHUV ZLOO GR VR
E\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFNDWLGOH
The action is not functional at high throttle to
DYRLGDFFLGHQWDOGHDGVWLFNODQGLQJV7KHVZLWFK¶V
ORFDWLRQDQGGLUHFWLRQPXVWEHFKRVHQDVLWGHIDXOWV
WR18//
7KURWWOHFXWVHWWLQJSURFHGXUH
1. Activate the function:
Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode.
Select the ACT mode by scrolling the touch
sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
function and return to the cursor mode.
2. Switch selection:
Move the cursor to the [SW] item and access
the switch setup screen by touching the
RTN button and select the switch and ON
direction.
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
3. Throttle cut position setting:
Move the cursor to the [POS] item and touch
the RTN button to switch to the data input
mode.
Adjust the servo operation position at throttle
cut operation by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
:LWKWKHVHOHFWHGFXWVZLWFK21DQGWKHWKURWWOHVWLFNDWLGOH
DGMXVWWKHUDWHXQWLOWKHHQJLQHFRQVLVWHQWO\FXWVRII
+RZHYHUEHVXUHWKDWWKHWKURWWOHOLQNDJHLVQRWSXOOHGWRR
tight or unreasonable force is not applied to the servo.
ŏ 6HOHFW >7+5 &87@ LQ WKH /LQNDJH PHQX DQG DFFHVV
the setup screen shown below by touching the
RTN button.
ŏ &XUUHQW WKURWWOH SRVLWLRQ
ŏ &XW SRVLWLRQ
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH