Futaba 8FG 2.4GHz - Manual (Page 118)

118 )XQFWLRQVRI0RGHO0HQX +HOLFRSWHU)XQFWLRQV !
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button.
<SensorTouch™>
*<52PL[LQJ
7KLV IXQFWLRQ XVHG WR DGMXVW J\UR VHQVLWLYLW\
7KHVHQVLWLYLW\DQGRSHUDWLRQPRGH 1RUPDOPRGH
$9&6PRGH FDQEHVHWIRUHDFKFRQGLWLRQ
7KHJ\URVHQVLWLYLW\FDQEHVZLWFKHGZLWKHDFK
FRQGLWLRQRUWKHVZLWFK VHQVLWLYLWLHV
ŏ 6HOHFW >*<52@ DW WKH 0RGHO PHQX DQG DFFHVV WKH
setup screen shown below by touching the RTN
button.
&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
ŏ0RGH VHOHFWLRQ
[AVCS]/[NORM]
ŏ*\UR W\SH VHOHFWLRQ
[GY]/[NORM]
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH
ŏ7R QH[W SDJH
ŏ6HWXS VFUHHQ VHOHFWLRQ
ŏ21 LQLWLDO VHWWLQJ
ŏ)LQH WXQLQJ 95 VHWWLQJV
ŏ*\UR VHQVLWLYLW\ DGMXVWPHQW
Note: Sensitivity setting is assigned to CH5 on
your receiver.
Always set to [--] both (Control) and (Trim) for
the [Gyro] function at the Function menu in
the Linkage menu.
6HWWLQJPHWKRG
Ɣ*\URW\SHVHOHFWLRQ
Move the cursor to the gyro type selection
item and touch the RTN button to switch to
the data input mode. Select the gyro type
by scrolling the touch sensor.
[GY]: When a Futaba GYA gyro is used
[NORM]: When other than Futaba GYA gyro
is used
Touch the RTN button to change the gyro
type and return to the cursor mode.
:KHQD)XWDED*<$J\URLVXVHGDQG>*<@W\SHLVVHOHFWHG
the sensitivity set value is directly read in both the AVCS
DQG1250PRGHV
Ɣ2SHUDWLRQPRGHVHOHFWLRQ *<$J\UR
Move the cursor to the operation mode
selection item and touch the RTN button
to switch to the data input mode. Select
the operation mode by scrolling the touch
sensor.
[AVCS]: AVCS mode
[NORM]: Normal mode
T o u c h t h e R T N b u t t o n t o c h a n g e t h e
operation mode and return to the cursor
mode.
Ɣ6HQVLWLYLW\VHWWLQJ
Move the cursor to the rate item and touch
the RTN button to switch to the data input
mode.
Adjust the sensitivity by scrolling the touch
sensor.
,QLWLDO YDOXH 
$GMXVWPHQW UDQJH a
:KHQ WKH 571 EXWWRQ LV WRXFKHG IRU RQH VHFRQG WKH
VHQVLWLYLW\LVUHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to return to the cursor
mode.
Ɣ)LQHWXQLQJ95VHWWLQJV
Move the cursor to the [--] item and touch
the RTN button to access the selection
screen. Select the control.
)RUDGHVFULSWLRQRIWKHVZLWFKVHOHFWLRQPHWKRGVHHWKH
description at the back of this manual.
Move the cursor to the rate item and touch
the RTN button to switch to the data input
mode.
Adjust the trim rate by scrolling the touch
sensor.
,QLWLDO YDOXH 
$GMXVWPHQW UDQJH a
:KHQ WKH 571 EXWWRQ LV WRXFKHG IRU RQH VHFRQG WKH
VHQVLWLYLW\LVUHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to return to the cursor
mode.
ŏ&RQGLWLRQ6ZLWFK VHOHFWLRQ