Futaba 8FG 2.4GHz - Manual (Page 17)

17 %HIRUH8VH!
Note:
6FUROORSHUDWLRQ &LUFOH\RXU¿QJHURQWKHRXWVLGHHGJHRI
the RTN button. The sensors may mis-read your touch as a
UHYHUVHURWDWLRQLIWKHFLUFOHLVVPDOOHURUSHUIRUPHGRQWKH
inside edge of the RTN button.
* The SensorTouch™ may not operate smoothly if your hand
LV WRXFKLQJ WKH VXUURXQGLQJ FDVH SDUWV $V VXFK SOHDVH
PDNHVXUHWKDWWKHWLSRI\RXU¿QJHULVDFWXDOO\RSHUDWLQJWKH
SensorTouch™.
,IWKH6HQVRU7RXFKŒGRHVQRWUHJLVWHU\RXULQSXWSOHDVH
WU\DJDLQDIWHUOLJKWO\WDSSLQJ\RXU¿QJHURQWKHVHQVRURQFH
again.
'RQRWRSHUDWHWKH6HQVRU7RXFKŒZLWKJORYHVZRUQ7KH
SensorTouch™ might not react.
ｎ CAUTION
ｊ 7KH WRXFK VHQVRU PLJKW QRW RSHUDWH E\
UHFHLYLQJ WKH VSDUN QRLVH JHQHUDWHG IURP
WKHJDVROLQHHQJLQHHWF,QWKLVFDVHSOHDVH
RSHUDWH \RXU WUDQVPLWWHU IURP WKH QRLVH
VRXUFHDSDUW
Stick Adjustment
$GMXVWPHQWRIWKHVWLFNOHYHUOHQJWK
<RXFDQDGMXVWWKHOHQJWKRIVWLFNOHYHUVDV\RX
OLNH,WLVUHFRPPHQGHGWRDGMXVWWKHOHQJWKRIWKH
VWLFNVLQOLQHZLWK\RXUKDQGVL]H
Lever Head
A
Lever Head
B
1. Hold the lever head "B" and turn the lever
head "A" counter-clockwise. The lock will be
released.
2. Turn the lever-head "A" clockwise as you hold
the lever-head "B" after placing it as you like.
$GMXVWPHQWRIVWLFNOHYHUWHQVLRQ
The tension of the self-return type stick lever can
EHDGMXVWHG
1. First, Remove the battery cover on the
bottom of the transmitter. Next, unplug the
battery wire and remove the battery from
the transmitter.
2. Next, using a screwdriver, remove the five
screws that hold the transmitter's rear case
in position, and put them in a safe place.
Gently ease off the transmitter's rear case.
Now you'll see the view shown in the figure
below.
•Stick Tension (J3)
(Mode 1) ( )
•Stick Tension (J4)
(Mode 1/2) ( )
•Stick Tension (J2)
(Mode 2) ( )
•Stick Tension (J1)
(Mode 1/2) ( )
2. Use a small Phillips screwdriver to adjust the
spring strength as you prefer by turning the
adjusting screw of the stick you want to
adjust.
7XUQLQJWKHVFUHZFORFNZLVHLQFUHDVHVWKHWHQVLRQ
CAUTION: If you loosen the screw too much,
the stick may not operate because it is
caught internally.
3) At the end of adjustment, re-install the rear
case.