Technical specifications – d&b D80 User Manual

Page 8

Advertising
background image

Audio data (linear setting with subsonic filter)

Maximum output power per channel (THD + N < 0.5%, all channels
driven)
CF = 6 dB @ 4/8 ohms

4 x 2600/2000 W

CF = 12 dB @ 4/8 ohms

4 x 4000/2000 W

Maximum output voltage

180 V

Frequency response (—1 dB)

35 Hz – 20 kHz

THD+N 20 Hz – 20 kHz, 600 W @ 4 ohms)

< 0.5%

S/N ratio (unweighted, RMS)
Analog input

> 110 dBr

Digital input

> 114 dBr

Damping factor (20 Hz – 200 Hz into 4 ohms)

> 100

Crosstalk (20 Hz – 20 kHz)

< –70 dBr

Gain (Linear mode @ 0 dB)

31 dB

Protection circuits

Mains inrush current limiter

13 A 

RMS

@ 230 V AC

22 A 

RMS

@ 120 V AC

27 A 

RMS

@ 100 V AC

Ground fault protection
Output current limitation/protection

65 A / 75 A

Output DC offset protection

10 V

Output HF Voltage Limiter

60 V @ 10 kHz

Output pop-noise suppression
Mains Current Limitation (MCL)

95 to 50 % of 16 / 30 A

Overvoltage protection

Up to 400 V AC

Self-resetting overtemperature protection

Power supply

Autosensing switched mode power supply with active power factor
correction (PFC)
Mains connector

powerCON-HC

Rated mains voltage

208 to 240 V, 50 – 60 Hz

high range

100 to 127 V, 50 – 60 Hz

low range

Mains fuse

internal

Power consumption (typical values)

Standby

9 W

Idle

180 W

Max. power consumption (short term RMS)

7000 W

Audio input connectors

INPUT analog (A1 - A4)

3 pin XLR female

Pin assignment

1 = GND, 2 = pos., 3 = neg.

Input impedance

38 kOhms, electronically balanced

Common mode rejection (CMRR @ 100 Hz/10 kHz)

> 70 / 50 dB

Maximum input level (balanced/unbalanced)

+25 / 17 dBu

+27 dBu @ 0 dBFS

LINK analog (A1 - A4)

3 pin XLR male

Pin assignment

1 = GND, 2 = pos., 3 = neg.

parallel to input

INPUT digital (D1/2, D3/4)

3 pin XLR female, AES 3

Pin assignment

1 = GND, 2 = AES Signal, 3 = AES Signal

Input impedance

110 ohms, transformer balanced

Sampling

48 / 96 kHz / 2 Ch/n

Synchronization

Word-Sync: PLL-locked to source (slave mode)

LINK digital (Output)

3 pin XLR male

electronically balanced

analog signal buffering (refresh), power fail relay (Bypass)

Output connectors

SPEAKER OUTPUTS A/B/C/D

4 x NL4

optional: 4 x EP5

4 CHANNEL OUTPUT

1 x NL8

Network connectors

CAN

2 x RJ 45 parallel

ETHERNET

2 x etherCON

®

Dual Ethernet port with built-in 2-port Ethernet switch

10/100 Mbit

Controls and indicators

POWER

Mains power switch

SCROLL/EDIT

Digital rotary encoder

Display

TFT color touch screen, 3.5" / 320 x 240 Pixel

2. Technical specifications

d&b D80 Manual 1.9 en

8

Advertising
This manual is related to the following products:

10D, 30D, D20