Document Outline

• CONTENT
• 1. Introduction
  • Chapter Structure
  • How to Use This Manual
  • Terms and Definitions
  • System Overview
  • Application Questions
• 2. Hardware Orientation
  • In This Chapter
  • VSP 628S Back Panel
    • CONT Interface
      • 1. Dial Switch
      • 2. 10/100M UDP Interface
      • 3. USB Interface
      • 4. RS232 Interface
    • INPUT Interface
      • 5~7：CVBS Input
      • 8：S-Video DIN 4
      • 9：VGA Input
      • 10：DVI Input
      • 12：SDI Loop Out
      • 13.14：SDI Input
      • 15.16.17：CVBS Loop Out
      • 18：S-Video Loop Out
      • 19：VGA Loop Out
      • 20：DVI Loop Out
    • OUTPUT Interface
      • 11：Sending Card/SDI output module port
      • 21：DVI Output
      • 22：DVI +VGA DVI Output
      • 23：CVBS Output
    • Switch and Power
      • 24.25：Power Interface and Switch
  • VSP 628S Front Panel
    • LCD Panel
    • Menu Buttons
    • Signal keys
    • Function
• 3. Hardware Installation
  • In This Chapter
  • Safety Precautions
  • Unpacking and Inspection
  • Site Preparation
• 4. Menu Orientation
  • In This Chapter
  • MENU
    • MENU---INPUT DETAIL
    • MENU---OUTPUT DETAIL
    • MENU--- SCREEN PARAMETER
    • MENU--- VIEW
    • MENU--- EFFECTS
    • MENU--- TEST PATTERN
    • MENU--- LED CARD
    • MENU--- SYSTEM
    • MENU--- TECH SUPPORT
    • MENU--- RESET
• 5. Communication Software Guideline
  • In This Chapter
  • Install Software
  • Run Software
    • Set Up Communication
    • How to use
      • File Toolbar
      • Communication Toolbar
      • Device Toolbar
      • Help Toolbar
      • Output resolution Toolbar
      • Display mode Toolbar
      • Layout Toolbar
      • Aspect Ratio Toolbar
      • Input Toolbar
      • Screen parameter Toolbar
      • Image Toolbar
      • Display Toolbar
      • Output Image Toolbar
      • Resolution Toolbar
      • User Mode Toolbar
      • Log Toolbar
      • Information Toolbar
      • 【VProcessor 】Options
      • 【Help 】options
  • How to control processor through RS232?
  • How to control processor with console software by USB?
  • How to Connect PC through LAN Interface?
• 6. System Setup and Operations
  • In This Chapter
  • Interface and Input Signal Option
  • Single Picture Signal Switch
    • Button Save User Mode Operations
    • Single Image Switch
    • LOGO/test pattern/black field switch
    • Scale
  • PIP Setting
    • Each Image Width, Height and Position Setting
    • Console Software Setting Each Image's Width, Height and Position.
  • How to Add Tasks
  • How to Realize LAN Remote Control Settings?
  • How to Achieve Cross-platform WEB setting?
• 7. Common Questions and Solution
  • In This Chapter
  • No Output in Large Screen
    • Confirm if there are any input singles
    • Confirm if signal output
  • Large Screen Output Flash Point
    • Confirm if monitor output is normal
  • Large Screen only Display Part of the Image
    • Signal need to scale
  • No Display in the Second Half Part of Large Screen
    • Resolution is inadequate
    • Sending card can't take lower part
  • Left of the Screen Appears Two Black Sides
    • Adjust DE deviation
  • All Key Lights Light Simultaneously
    • Check if dial switches are normal
• A. Specification
• V1.3 VSP 628S With CS Module
  • a. CVBS Output Module
  • b. SDI output module
• V1.4 VSP 628S With SDI Module
  • a.VSP 628S add SDI output Module
  • b. How to replace VSP 628S back panel block to SDI output block?
  • c. WEB SERVER cross-platform control operation interface
• B. Contact Information
• C. Upgrading Software
  • Download the IP software