Heatiator C40 - Manual (Page 2)

Page 2 Heatilator • Constitution EPA Fireplace • 480-1091D 4/20/11
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future references.
Congratulations
Congratulations on selecting a Heatilator wood burning
fireplace. The Heatilator fireplace you have selected is
designed to provide the utmost in safety, reliability, and
efficiency.
As the owner of a new fireplace, you'll want to read and
carefully follow all of the instructions contained in this
Owner's Manual. Pay special attention to all Cautions and
Warnings.
This Owner's Manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Your new Heatilator wood burning fireplace will give you
years of durable use and trouble-free enjoyment. Welcome
to the Heatilator family of fireplace products!
Listing Label Information/Location
The model information regarding your specific appliance can
be found on the rating plate usually located in the control
area of the appliance.
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number: __________________________________________ Location on appliance: ____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
We recommend that you record the following pertinent
information about your appliance.
Homeowner Reference Information
Model:
C
ONSTITUTION
E
PA
C
ERTIFIED
F
IREPLACE
Serial No / Numéro De Série
OMNI-Test Laboratories, Inc.
Report #061-S-40-2
LISTED FIREPLACE, SOLID FUEL TYPE, ALSO SUITABLE FOR MANUFACTURED
HOME INSTALLATION. (UM) 84 HUD. "For Use with Solid Wood Fuel Only."
Install and use only in accordance with manufacturer's installation, venting and operating instructions.
Any area incorporating warm or cold air ducts shall be enclosed in accordance with the manufacturer's
installation instructions.
Contact Your Local Building Or Fire Officials Or Authority Having Jurisdiction About Restrictions,
Installation Inspection And Permits Required In Your Area.
WARNING - For Manufactured Homes: Do not install in a sleeping room. An outside combustion air
inlet must be provided and unrestricted while unit is in use. The structural integrity of the manufactured
home floor, ceiling and walls must be maintained. The fireplace needs to be properly grounded to the
frame of the manfactured home.
Components required for installation: HTI SLSeries Pipe, Termination Cap, Hearth Extension and required
accessory Chimney Air Kit Part CAK4A.
Do not connect this unit to a chimney serving another appliance.
DANGER: Risk of electrical shock. Disconnect power supply before servicing.
Electrical Rating: 115 VAC <3.0 AMPS 60 Hz
Do not use grate or elevate fire. Build wood fire directly on firebrick.
Do not overfire. If heater or chimney connector glows, you are overfiring.
Do not use a fireplace insert or other products not specified for use with this product.
WARNING - THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED GAS LOG SET OR ANY LOG SET.
TO REDUCE RISK OF FIRE OR INJURY, DO NOT INSTALL AN UNVENTED GAS LOG SET OR ANY LOG SET INTO
FIREPLACE.
Must provide a source of air to prevent air starvation from combustion which could result of high levels of
carbon monoxide.
Replace glass only with 5mm ceramic available from your dealer.
Optional Fire Screen Part Mesh-EPA, may be used ONLY in USA
Chimney sections at any level require a 2” (51mm) minimum
air space clearance between the framing and chimney section.
Minimum Clearances To Combustible Material
WITHIN ENCLOSURE AREA
Appliance to backwall 1" (25mm)
Appliance to sidewall 1" (25mm)
Duct boots to framing 0" (0mm)
Top standoffs to header 0" (0mm")
EXPOSED SURFACES
Faceplate to sidewall 16" (406mm)
Remote outlet air grills to ceiling 12"(305mm)
MANTEL
Mantel from base of fireplace 60" (1524mm)
Maximum mantel depth 12" (305mm)
FLOOR PROTECTION
Combustible flooring 20" (508mm) in front of and 8" (203mm) to
either side of the fuel opening must be insulated with
non-combustible floor protection with a minimum thickness of 1"
(25mm) and ("k" value = 0.43).
In Canada: The hearth extension must be installed according to
the installation instructions.
U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to comply with July 1990 particulate emission standards.
2011 2012 2013 Jan Feb Mar Apr May June July Aug Sept Oct. Nov. Dec.
Made in U.S.A DO NOT REMOVE THIS LABEL 480-1110
Mfg by:
www.heatilator.com
TESTED TO
UL 127, ULC-S610-M87
SA
MP
LE
009
O-T L Tested and
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C US
A division of Hearth & Home Technologies Inc.
1915 W. Saunders, Mt. Pleasant, IA 52641
www.heatilator.com