Garland MP-GD-10-S - Manual (Page 23)

Part # MPSM07 (03/24/08) Page 23
Programming Recipe Keys
For “one touch” cooking, each of the numeric keys, (1 through
9), on the keypad can be programmed to contain a product
recipe consisting of 1 to 6 “profiles .” Each profile consists of
a set of cooking parameters which control that profile’s fan
speed, cook temperature, cook time and moisture settings .
To program a recipe key:
1 . Press and hold the Program key for 3 seconds . The display
will indicate ENTER CODE . Here, a pass code must be
entered . This security feature prevents unauthorized
persons from changing recipe parameters .
2 . Use the numeric keys to enter 4 - 2 - 7 - 5 . Then press the
Y/Enter key .
3 . Press the N/Scroll key to select recipe or system
programming .
4 . The display will indicate PRESS KEY TO PROGRAM . Choose
the desired numeric key to which the new recipe will be
assigned, and press that key .
Press the Y/Enter key . The display will indicate PROGRAM
SHELF . Press the N/Scroll key .
5 . The display will indicate PROGRAM FAN PROF1 SPEED .
Press the N/Scroll key repeatedly to step through the
available fan speed choices, (HIGH, LOW, PULSE), until the
desired speed for Profile 1 is displayed .
6 . Press the Y/Enter key . The fan setting will be stored and
the display will indicate PROGRAM PROF1 COOK TEMP . Use
the numeric keys to enter the desired cook temperature .
Enter a number between 150 and 500, (factory default is
350) . If a number outside this range is entered, the control
will sound an error tone and reset to the closest allowable
number within the range .
7 . Press the Y/Enter key . This stores and implements the
Profile 1 temperature setting . The display will indicate
PROGRAM PROF1 COOK TIME . Use the numeric keys to
enter the desired cooking time in hours, minutes and
seconds .
Each time a key is pressed, the numbers displayed move
one position left . It may be necessary to enter zeros first
to attain the desired result, for instance, to enter a time
of 30 minutes, press, 0 - 0, (hours), 3 - 0, (minutes), 0 - 0,
(seconds), resulting in a timer display of “00:30:00 .”
8 . Press the Y/Enter key . This stores and implements the
Profile 1 Cook time setting . The display will indicate
PROGRAM PROF1 MOISTURE .
Press the N/Scroll key repeatedly to step through the
available moisture setting choices until the desired setting
is displayed . Moisture setting presets for Meat, Bread,
Poultry, Fish and None are included, along with a User
setting to allow for custom moisture settings . See “User
Moisture Settings,” on page 26 for more information .
9 . Press the Y/Enter key . This stores and implements the
Profile 1 moisture setting . The display will indicate
CONTINUE Y/N .
10 . To continue on to Profile 2 of the recipe, press the Y/Enter
key and enter cooking parameters for Profile 2 as done for
profile 1 in steps 4 through 9 . Up to 6 full profiles may be
entered in this way for a single recipe .
To end cook cycle programming of a recipe after any of
profiles 1 through 6 has been entered, choose NO at the
CONTINUE prompt by pressing the N/Scroll key .
11 . The display will indicate PROGRAM HOLD Y/N . Press the
Y/Enter key if a Hold cycle is desired for the recipe, or
N/Scroll if a Hold cycle is not desired .
12 . If NO was chosen in step 10, skip directly to step 12 .
If YES was chosen in step 11, the display will indicate
PROGRAM HOLD TEMP . Use the numeric keys to enter the
desired Hold temperature .
Enter a number between 140 and 210, (factory default is
160) . If a number outside this range is entered, the control
will sound an error tone and reset to the closest allowable
number within the range . If a new Hold temperature
is not entered, the control will use the most recently
programmed Hold temperature .
Press the Y/Enter key . This stores and implements the Hold
temperature setting .
13 . The display will indicate CONTINUE Y/N . To end recipe key
programming, press the N/Scroll key .
To program another recipe key, press the Y/Enter key and
repeat the procedure, beginning with step 3 .
System Program Options
To change the system setting, follow steps 1 & 2 above, use
the
N/Scroll key to select system programing and press Y/Enter to
begin .
Program options are:
Manual Bake ON/OFF
Light Mode ON/OFF
Ready Band ON/OFF
Flexible or Straight Time Select