Sharp AR-M700N User Manual
Page 9
0-5
CONTENTS
Page
PRODUCT CONFIGURATIONS .................................. 0-1
OPERATION MANUALS.............................................. 0-1
INSTALLATION REQUIREMENTS.............................. 0-2
CAUTIONS................................................................... 0-3
● Laser Information ................................................. 0-4
CONTENTS ................................................................. 0-5
CHAPTER 1
BEFORE USING THE PRODUCT
INTRODUCTION.......................................................... 1-2
MAIN FEATURES ........................................................ 1-3
PART NAMES AND FUNCTIONS ............................... 1-9
● Exterior................................................................. 1-9
● Interior .................................................................. 1-10
● Operation panel.................................................... 1-12
● Touch panel ......................................................... 1-13
TURNING THE POWER ON AND OFF ....................... 1-16
AUDITING MODE ........................................................ 1-17
● Using the machine when the auditing mode is
enabled ................................................................ 1-17
LOADING PAPER........................................................ 2-2
● Identifying the trays .............................................. 2-2
● Loading paper in paper tray 1 - tray 2 .................. 2-2
● Loading paper in paper tray 3 .............................. 2-3
● Changing the paper size in paper tray 3 .............. 2-3
● Changing the paper size in paper tray 4 .............. 2-4
● Loading paper in paper tray 5 (optional large
capacity tray) ..................................................................2-5
● Specifications (optional large capacity tray)......... 2-5
● Loading paper in the bypass tray ......................... 2-6
● Specifications of paper trays (Types and sizes of
paper that can be used in the trays)..................... 2-8
● Setting the paper type and paper size ................. 2-10
● Setting the paper size when a special size is
loaded .................................................................. 2-12
CUSTOM SETTINGS................................................... 2-13
● General procedure for custom settings ................ 2-13
● About the settings ................................................ 2-15
REPLACING THE TONER CARTRIDGES .................. 2-16
STORAGE OF SUPPLIES ........................................... 2-17
MISFEED REMOVAL................................................... 2-18
● Misfeed removal guidance ................................... 2-18
● Misfeed in the transport area, fusing area, and
exit area ............................................................... 2-19
● Misfeed in the duplex unit .................................... 2-20
● Misfeed in the paper feed area ............................ 2-21
REMOVING AN ORIGINAL MISFEED ........................ 2-25
● Removing a misfed original from the automatic
document feeder .................................................. 2-25
TROUBLESHOOTING ................................................. 2-26
FINISHER AND SADDLE STITCH FINISHER .............3-2
● Part names ...........................................................3-2
● Specifications .......................................................3-2
● Finishing methods ................................................3-4
● Finishing modes and finisher functions ................3-6
● Staple cartridge replacement and staple jam
removal.................................................................3-7
● Removing a misfeed.............................................3-11
● Troubleshooting finisher/saddle stitch finisher
problems...............................................................3-13
INSERTER ...................................................................3-14
● Part names ...........................................................3-14
● Specifications .......................................................3-14
● Loading paper.......................................................3-15
● Manual operation of the inserter...........................3-15
● Misfeed removal ...................................................3-17
● Troubleshooting inserter problems .......................3-18
AUTOMATIC DOCUMENT FEEDER ...........................4-2
● Acceptable originals .............................................4-2
PLACING ORIGINALS .................................................4-3
CHECKING THE SIZE OF A PLACED ORIGINAL ......4-5
● Manually setting the scanning size.......................4-5
STORING, DELETING, AND USING ORIGINAL
SIZES ...........................................................................4-6
● Storing or deleting an original size .......................4-6
NORMAL COPYING.....................................................4-7
● Making copies with the automatic document
feeding function ....................................................4-7
● Automatic two-sided copying using the automatic
document feeding function ...................................4-10
● Copying from the document glass ........................4-11
● Automatic two-sided copying from the document
glass .....................................................................4-13
ADJUSTING THE EXPOSURE ....................................4-14
REDUCTION/ENLARGEMENT/ZOOM ........................4-15
● Automatic selection (auto image) .........................4-15
● Manual selection (preset copy ratios/zoom) .........4-16
● XY ZOOM .............................................................4-18
SPECIAL PAPERS.......................................................4-20