Document Outline

• NI CVS-1450 Series User Manual
• Support
  • Worldwide Technical Support and Product Information
  • National Instruments Corporate Headquarters
  • Worldwide Offices
• Important Information
  • Warranty
  • Copyright
  • Trademarks
  • Patents
  • WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS
• Compliance
• Conventions
• Contents
• Chapter 1 NI CVS-1450 Series Overview
  • About the NI CVS-1450 Series
  • Hardware Overview
    • Figure 1-1. CVS-1450 Series Front Panel
  • Available Camera Bandwidth
    • Table 1-1. Available Camera Bandwidth
  • Software Overview
    • NI-IMAQ for IEEE 1394 Cameras Driver Software
    • National Instruments Application Software
      • Vision Builder for Automated Inspection
      • LabVIEW Real-Time Module with the Vision Development Module
• Chapter 2 Setup and Configuration
  • Required Items
    • Hardware
    • Software
  • Accessories
    • Hardware
  • Documentation
    • Hardware Documents
    • Vision Builder AI Documents
    • NI-IMAQ for IEEE 1394 Cameras Driver Software Documents
    • Vision Development Module and LabVIEW Real-Time Module Documents
      • Vision Development Module Documents
      • LabVIEW Real-Time Module Documents
  • Safety Information
  • Setup Overview
    • Figure 2-1. Setup Sequence
    • Before Getting Started: Connecting the CVS-1450 Device to a Network
      • Subnet Considerations
  • Setting Up the Hardware
    • Connecting a Camera and Monitor to the CVS-1450 Device
      • Figure 2-2. Basic Hardware Setup
    • Wiring Power to the CVS-1450 Device
      • Figure 2-3. Wiring Power to the CVS-1450 Device
    • Connecting to a Separate Main Supply
      • Figure 2-4. Wiring a Third-Party Power Supply to the 4-Position Power Connector
    • Connecting the CVS-1450 Device to the Development Computer
      • Figure 2-5. Ethernet Connection
  • Vision Builder AI: Setting up the Development Computer
    • Installing Vision Builder AI and NI-IMAQ for IEEE 1394 Cameras
    • Configuring the IP Address on the CVS-1450 Device
  • Acquiring an Image in Vision Builder AI
  • LabVIEW Real-Time Module with the Vision Development Module: Setting up the Development Computer
    • Installing the LabVIEW Real-Time Module, Vision Development Module, and NI-IMAQ for IEEE 1394 Cameras
    • Configuring the IP Address using the LabVIEW Real-Time Module
    • Downloading Software onto the CVS-1450 Device
  • Acquiring an Image Using the LabVIEW Real-Time Module
• Chapter 3 LEDs, DIP Switches, and Connectors
  • LED Indicators
    • Figure 3-1. POWER OK and STATUS LEDs
    • POWER OK LED
    • STATUS LED
    • ACT/LINK LED
    • 100 Mbps LED
      • Figure 3-2. ACT/LINK and 100 Mbps LEDs
  • DIP Switches
    • Figure 3-3. DIP Switches
    • SAFE MODE Switch
    • IP RESET Switch
    • NO APP Switch
    • USER 1 Switch (LabVIEW Real-Time Module Users)
  • Connectors
    • Table 3-1. CVS-1450 Device Connectors Overview
    • Power Connector
      • Figure 3-4. Power Connector
      • Table 3-2. Power Connector Terminals
      • Earth Ground Connection
      • Figure 3-5. Grounding Lug on the CVS-1450 Device
    • IEEE 1394
    • VGA
      • Figure 3-6. VGA Connector
      • Table 3-3. VGA Connector Signals
    • COM1
      • Figure 3-7. COM1 DSUB 9-Pin Connector
      • Table 3-4. COM1 Connector Signals
    • Ethernet
    • TRIG 0
    • TRIG 1 and TRIG 2
    • General-Purpose Digital I/O
      • Figure 3-8. 44-Pin DSUB Connector
      • Table 3-5. 44-Pin DSUB and 37-Pin Terminal Block Connector Signals
• Chapter 4 Digital I/O Functionality
  • Overview
  • TTL and Isolated Inputs and Outputs
    • TTL Inputs and Outputs
      • Table 4-1. TTL Inputs and Outputs
    • Isolated Inputs and Outputs
      • Table 4-2. Isolated Inputs and Outputs
    • I/O for Normal Operation
      • Trigger Inputs
      • Timed Pulse Output
      • Figure 4-1. Output Pulse When Trigger Is Selected
      • Figure 4-2. High Pulse with Rising Edge Trigger
      • Figure 4-3. High and Low Pulse Trains
      • Quadrature Encoder
      • Figure 4-4. Rising Edge Trigger, Low Pulse with a Quadrature Encoder Delay
      • Product Selection Port
      • Table 4-3. Product Selection Port
      • General-Purpose I/O
    • I/O for Fault Conditions
      • Table 4-4. Configuration Settings and Effects
      • Shutdown
      • Watchdog Timer
      • Overheat
  • Considerations When Connecting the Digital I/O
    • Wiring an Isolated Input to a Sourcing Output Device
      • Figure 4-5. Example of Connecting an Isolated Input to a Sourcing Output Device
    • Wiring an Isolated Output to an External Load
      • Figure 4-6. Example of Connecting an Isolated Output to an External Load
    • Protecting Inductive Loads
      • Figure 4-7. Example of Using an External Flyback Diode for Inductive Loads
    • Transmission Line Effects
      • Figure 4-8. Example Connections
  • Typical System Setup
    • Table 4-5. Typical Single-Camera System Setup
    • Figure 4-9. Typical Single-Camera Setup
• Chapter 5 Deployment
  • Connecting Multiple CVS-1450 Devices
    • Figure 5-1. Multiple CVS-1450 Devices Connected to the Same Network
    • Figure 5-2. Serial Number and MAC Address Label on the CVS-1450 Device
    • Figure 5-3. CVS-1450 Device Connected to a Monitor
• Appendix A Troubleshooting
  • Table A-1. STATUS LED Flashes and Corresponding Error Conditions
• Appendix B Specifications
• Appendix C Mounting Information
  • Figure C-1. Back View of the CVS-1450 Series with Dimensions
  • Figure C-2. Side View of the CVS-1450 Series with Dimensions
  • Figure C-3. Bottom View of the CVS-1450 Series with Dimensions
  • Figure C-4. Space and Cabling Clearance for the CVS-1450 Series
• Appendix D Technical Support and Professional Services
• Glossary
  • B-I
  • L-T
  • U-V
• Index
  • Numerics
  • A-D
  • E-I
  • K-Q
  • R-V
  • W