Xylem e-NSCS - Manual (Page 12)

1 Introduction and Safety
1.1 Introduction
Purpose of this manual
The purpose of this manual is to provide necessary information for:
• Installation
• Operation
• Maintenance
CAUTION:
Read this manual carefully before installing and using the
product. Improper use of the product can cause personal in-
jury and damage to property, and may void the warranty.
NOTICE:
Save this manual for future reference, and keep it readily available at
the location of the unit.
1.1.1 Inexperienced users
WARNING:
This product is intended to be operated by qualified person-
nel only.
Be aware of the following precautions:
• Persons with diminished capacities should not operate the prod-
uct unless they are supervised or have been properly trained by a
professional.
• Children must be supervised to ensure that they do not play on or
around the product.
1.2 Safety terminology and symbols
About safety messages
It is extremely important that you read, understand, and follow the
safety messages and regulations carefully before handling the product.
They are published to help prevent these hazards:
• Personal accidents and health problems
• Damage to the product
• Product malfunction
Hazard levels
Hazard level Indication
DANGER:
A hazardous situation which, if not
avoided, will result in death or se-
rious injury
WARNING:
A hazardous situation which, if not
avoided, could result in death or
serious injury
CAUTION:
A hazardous situation which, if not
avoided, could result in minor or
moderate injury
NOTICE:
• A potential situation which, if
not avoided, could result in
undesirable conditions
• A practice not related to per-
sonal injury
Hazard categories
Hazard categories can either fall under hazard levels or let specific
symbols replace the ordinary hazard level symbols.
Electrical hazards are indicated by the following specific symbol:
Electrical Hazard:
These are examples of other categories that can occur. They fall under
the ordinary hazard levels and may use complementing symbols:
• Crush hazard
• Cutting hazard
• Arc flash hazard
Hot surface hazard
Hot surface hazards are indicated by a specific symbol that replaces
the typical hazard level symbols:
CAUTION:
Description of user and installer symbols
Specific information for personnel in charge of installing
the product in the system (plumbing and/or electrical
aspects) or in charge of maintenance.
Specific information for users of the product.
Instructions
The instructions and warnings that are provided in this manual concern
the standard version, as described in the sales document. Special ver-
sion pumps may be supplied with supplementary instruction leaflets.
Refer to sales contract for any modifications or special version charac-
teristics. For instructions, situations, or events that is not considered in
this manual or the sales document, contact the nearest Lowara Serv-
ice Center.
1.3 Disposal of packaging and product
Observe the local regulations and codes in force regarding sorted
waste disposal.
1.4 Warranty
For information about warranty, see the sales contract.
1.5 Spare parts
WARNING:
Only use original spare parts to replace any worn or faulty
components. The use of unsuitable spare parts may cause
malfunctions, damage, and injuries as well as void the guar-
antee.
CAUTION:
Always specify the exact product type and part number
when requesting technical information or spare parts from
the Sales and Service Department.
For more information about the product's spare parts, see Figure 1 ,
Figure 2 , or Figure 3
1.6 EC DECLARATION OF CONFORMITY
XYLEM SERVICE ITALIA S.R.L., WITH HEADQUARTERS IN VIA VIT-
TORIO LOMBARDI 14 - 36075 MONTECCHIO MAGGIORE VI - ITA-
LIA, HEREBY DECLARES THAT THE FOLLOWING PRODUCT:
ELECTRIC PUMP UNIT (SEE LABEL ON FIRST PAGE)
FULFILS THE RELEVANT PROVISIONS OF THE FOLLOWING EU-
ROPEAN DIRECTIVES:
• MACHINERY DIRECTIVE: 2006/42/EC (THE TECHNICAL FILE
IS AVAILABLE FROM XYLEM SERVICE ITALIA S.R.L.).
• ELECTROMAGNETIC COMPATIBILITY 2004/108/EC
• ECO-DESIGN 2009/125/CE, REGULATION (EC) No. 547/2012,
REGULATION (EC) 640/2009 (3 ~, 50 Hz, PN≥ 0,75 kW) IF IE2
or IE3 MARKED
AND THE FOLLOWING TECHNICAL STANDARDS
• EN 809, EN 60335-1, EN 60335-2-41, EN 62233
• EN 61000-6-1:2007, EN 61000-6-3:2007
• EN 60034–30
• EN 953 :1997+A1:2009
• EN ISO 12100 :2010
• EN 60204-1 :2006/A1:2009
PUMP (SEE LABEL ON THE FIRST PAGE)
FULFILS THE RELEVANT PROVISIONS OF THE FOLLOWING EU-
ROPEAN DIRECTIVES
• MACHINERY 2006/42/EC (THE TECHNICAL FILE IS AVAILA-
BLE FROM XYLEM SERVICE ITALIA S.R.L.).
AND OF THE FOLLOWING TECHNICAL STANDARDS:
• EN 809
• EN 953 :1997+A1:2009
• EN ISO 12100 :2010
en - Translation of the original instructions
12 e-nscs Installation, Operation, and Maintenance Manual