Controlled Products Systems Group 9000-080 - Manual (Page 34)

9000-065-F-9-10 32
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
NC NO
1
2
3
4
5
6
7
8
9
13
12
11
10
14
15
16
17
18
19
20
4
1
2
3
Com
Com
Com
4405-010
PU SH TO O PE RA TE
tec hn ici an us e o nly
Power
Gate Tracker - DoorKing Access Control System (Model 1833, 1835, 1837 or 1838)
tracker system can be connected. This system can keep track of gate operator cycle
count, shorted inputs, loop detector problems, any forced entry attempts, if the gate
has struck anything during the open or close cycle, power interruptions, etc. For more
detailed information refer to the Tracker Installation and Wiring Manual, DoorKing P/N
2351-010.
Terminal #2 (Full open) or #5 (Partial open) required only if the tracker board will
activate the gate operator. Refer to the manual 2351-065 for detailed information.
5.2 Control Wiring
Power is limited
to 250 mamps.
Switch 3 Must be ON.
Power (24-Volt DC) and
logic output. Power is shut
off .5 sec. prior to gate
starting and remains off
while gate is opening and
in the open position.
#4 Com
White
24 Volt
1 amp max.
Stand-Alone
Key Switch
Safety
Opening
Device
Stand-Alone
Keypad
Stand-Alone
Card Reader
Telephone
Entry
“Closing-Direction” Photo Sensors
4-Pin Non-Removable Terminal
20-Pin Main
Terminal
Note: All stand-alone
and telephone entry devices must
use a separate power source.
Note: When
using 3-button
control station
AND interlock
switch together,
#3 terminal
(N.C.) must be
wired in series.
Remote Alarm Reset Station
(DKS P/N 1404-080) MUST be mounted
in the line-of-sight of the gate operator.
3-Button Control Station
Use a standard 4-wire 3-button
control station. DoorKing’s
3-wire 3-button control station
cannot be used.
Normally Closed Interlock Switch
SW 1, switch 5: After photo
sensor beam gets obstructed:
OFF- Reverses gate.
Partial
Open
Full
Open
Full
Open
#3 Stop N.C.
#2 Close N.O.
#1 Open N.O.
3-Wire Radio
Receiver
To #4 Com
To #3 Stop N.C.
N.O.
N.C.
Com
Operator Cycling
Lock Engaged
N.O.
N.C.
Com
Operator Stopped
Lock Disengaged
Red Blue
Alarm
Alarm
Reset
#5 Terminal Note: Any opening device connected to terminal #5 will
open the gate to the partial open setting. Secondary entrapment
protection devices will also open the gate to the partial open setting.
If the inherent reverse sensor gets activated during the close cycle,
it will always fully open the gate.
OPEN
STOP
CLOSE
SW 1
1 ON
2
3
4
5
6
7
8
SW 1
1 ON
2
3
4
5
6
7
8
Com 24 V
olt
Relay
1 Mo tor 2 Mo tor 3 Ne utr al 4 24 VA C 5 Limi t 6 Sp are 7 Limi t 8 COM
3-Pin
Remote
Terminal
1 2 3
Place jumper
on bottom
2 pins when
using 4-pin
terminal.
3-Pin With
Jumper
Magnetic Lock
Quad Box
#4 Normally Open
#2 Normally Open
#6 Normally Open
#9 Normally Close
ON - Stops gate then continues
closing when gate is clear (Same
function as UL 325 terminal #2).
Note: The ON setting is used to help prevent
tailgating but the photo sensor should be wired to
the UL 325 terminal #2 when the “stop gate”
function is desired, see pages 27 and 28 for more
information.